FabioT. Chassis Paint - 400ml - Green
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
The FabioT. RT 2K PU265 HS Chassis Topcoat is designed for professionals and serious DIYers seeking durable, high-performance protection for truck and commercial vehicle chassis. Its key benefit is superior corrosion and weather resistance thanks to a zinc phosphate reinforcement, offering a long-lasting semi-gloss finish. A potential caveat is its fast drying time, requiring efficient application to avoid lap marks.
All features
| Colour | Green |
|---|---|
| Model Part Number | FT-PU265-400AER-S-GS |
| Brand | FT Paints |
| Container Volume | 400ml |
Extended Product Information
FAQs
What is the shelf life of the 400ml aerosol can before activation?
Before the 2K activation, the aerosol can has a typical shelf life of 1-2 years when stored in a cool, dry place away from direct sunlight. Once activated, the pot life is limited (refer to product instructions, usually around 12-24 hours).
How long does it take to fully cure?
The coating is dust-dry in 15-30 minutes. However, a full cure, meaning maximum hardness and chemical resistance, is achieved in 7-8 days under standard conditions (approx. 20°C).
Can I use this on painted surfaces?
It is best applied to bare, prepared metal. If applying over existing paint, ensure the paint is sound, degreased, and lightly abraded for adhesion. Test compatibility in an inconspicuous area first.
What is the coverage rate?
Coverage varies depending on application thickness and surface porosity. A 400ml aerosol typically covers approximately 0.5-1.0 square meters at the recommended film thickness.
Is this product available in other colors?
Yes, the 2K PU265 HS Chassis Topcoat is available in other colors, including Grey and Black, and in larger container sizes. The 400ml aerosol is available in Green.
What safety precautions should I take?
Always use in a well-ventilated area. Wear appropriate personal protective equipment, including solvent-resistant gloves, eye protection, and a respirator suitable for organic vapors.
Troubleshooting
Uneven finish or "fisheyes"
Ensure surfaces are impeccably clean and free from silicone, oil, or grease contamination. Check for contamination in the spray equipment.
Runs or drips
Apply the coating in thinner, even coats. Reduce spraying distance or adjust spray pattern. Ensure the surface is not being over-applied.
Poor adhesion
Verify that the surface was properly cleaned, degreased, and free of rust. Ensure appropriate primers were used if necessary. Check for adequate drying/curing of primers.
Aerosol can not spraying
Ensure the nozzle is clear. Shake the can vigorously. If using the 2K activation, ensure the internal components have been properly mixed and allowed to stand as per instructions.
Pros and Cons
Pros
- Excellent durability and protection against corrosion and the elements.
- Professional semi-gloss finish enhances the appearance of chassis components.
- Strong adhesion ensures the coating stays put, even on demanding surfaces.
- Fast drying times improve application efficiency.
- High heat resistance makes it suitable for areas with elevated temperatures.
Cons
- Fast drying can lead to lap marks if application is not swift and even.
- Requires proper ventilation and personal protective equipment due to its formulation.
- Best results often achieved with professional spraying equipment.
- May require specific surface preparation for optimal adhesion.
- The 400ml aerosol is best suited for smaller touch-ups or components, not entire chassis.
Setup, Compatibility & Care
Setup:
For the 400ml aerosol, ensure the can is thoroughly shaken for at least two minutes before use. Activate the 2K system as per the specific instructions on the can (typically by releasing a button or plunger to mix the two components). Allow the can to stand for the time indicated on the instructions before spraying.
Compatibility:
This topcoat is designed to adhere to properly prepared steel, galvanized steel, and aluminium surfaces. It is recommended to use appropriate primers for optimal adhesion and corrosion protection, especially on bare metal. It is not recommended for use over existing paint systems unless compatibility is confirmed and the surface is appropriately prepared.
Care:
Once fully cured, the surface is highly resistant to cleaning agents. For routine maintenance, a simple wash with water and mild detergent is sufficient. Avoid abrasive cleaners or tools that could scratch the semi-gloss finish. Ensure good ventilation during application and allow adequate curing time before exposing the treated area to heavy use or harsh conditions.