Ft Paints Chassis Paint - 1.10 L Kit - Reseda Green
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This guide is for owners and maintainers of commercial vehicles and trucks looking for a durable, protective coating for their chassis. The Ft Paints 2K PU265 HS Chassis Topcoat offers a semi-gloss, high-build finish with excellent corrosion and weather resistance, primarily delivering long-lasting protection. A key consideration is that this is a 2K (two-component) system requiring mixing with a hardener and thinner, demanding proper preparation and application techniques.
All features
| Colour | Green |
|---|---|
| Model Part Number | 2K PU265 HS |
| Brand | FT Paints |
| Container Volume | 1100 |
Extended Product Information
FAQs
What is the shelf life of the unmixed product?
The shelf life of the unmixed components is typically 12 months when stored in a cool, dry place in original, sealed containers.
How long does it take for the chassis to be fully cured and ready for heavy use?
Under standard conditions (e.g., 20°C and 50% relative humidity), the coating achieves full cure in approximately 7-8 days. Avoid heavy use until full cure is achieved.
Can this product be applied over existing paint or coatings?
Yes, it can be applied over existing, sound paintwork provided it is thoroughly cleaned, degreased, and abraded (scuffed) to ensure adhesion. For best results, consult the product's technical data sheet for specific primer recommendations.
What safety precautions should I take when using this product?
Always use in a well-ventilated area. Wear appropriate personal protective equipment, including solvent-resistant gloves, eye protection, and a respirator suitable for organic vapors and particulates. Refer to the Safety Data Sheet (SDS) for detailed information.
What is the recommended film thickness?
The recommended dry film thickness per coat is typically between 50-75 microns, with a total DFT of 100-150 microns for optimal protection. Refer to the technical data sheet for precise recommendations.
Can I apply this in cold weather?
Application is generally recommended between 10°C and 30°C. Applying in temperatures below 10°C can significantly slow down curing and affect the final finish and properties. If applying in cooler conditions, ensure the substrate is dry and free from condensation.
Troubleshooting
Paint is too thick or difficult to apply
Ensure the correct amount of thinner has been added during mixing. Check ambient temperature; thinning may need adjustment based on conditions.
Poor adhesion to the surface
Verify the substrate was properly cleaned and degreased before application. Ensure the correct primer was used or that the surface was adequately prepared if unprimed.
Uneven or rough finish
Check spray gun settings (pressure, nozzle size) and application technique. Ensure even coat thickness and adequate flash-off time between coats. Avoid over-thinning or applying in adverse temperature/humidity conditions.
Coating remains tacky after extended drying time
Confirm correct mixing ratio of paint and hardener. Ensure application occurred within the recommended temperature and humidity range. Insufficient hardener or improper conditions can inhibit curing.
Pros and Cons
Pros
- Provides robust, long-lasting protection against corrosion and environmental factors.
- High-build formula offers excellent coverage and a professional semi-gloss finish.
- Suitable for a wide range of application methods.
- Good adhesion to various metal surfaces commonly found on vehicle chassis.
- Enhanced durability due to heat and UV resistance.
Cons
- Requires mixing of two components (paint and hardener) plus thinner, demanding precision.
- Long full cure time of 7-8 days may impact vehicle downtime.
- Specific application conditions (temperature, humidity) may affect drying and finish.
- Requires proper ventilation and personal protective equipment due to chemical nature.
Setup, Compatibility & Care Instructions
Setup:
This product is a 2K (two-component) system. It must be mixed with the corresponding hardener and thinner before application. The recommended mix ratio for the 1.10L kit is approximately 4 parts paint, 1 part hardener, and 0.8 parts thinner by volume. Always refer to the product's Technical Data Sheet for precise ratios and induction times. Ensure adequate ventilation during mixing and application.
Compatibility:
- Substrates: Bonds well to properly prepared steel, galvanised steel, and aluminium.
- Primers: Compatible with recommended primers for automotive chassis applications. Always test compatibility on a small area if unsure.
- Application Equipment: Suitable for electrostatic, Airmix, Airless spray guns, and brush application.
Care:
- Cleaning: Clean application equipment immediately after use with a suitable solvent cleaner. The coated chassis surface should be cleaned using mild detergents and water. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
- Maintenance: Regularly inspect the chassis for any signs of damage or corrosion and address promptly. The durable finish is designed for minimal maintenance.