FabioT. FT Paints 2K PU265 HS Chassis Paint - 2750ml - Red
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
The FabioT. FT Paints 2K PU265 HS Chassis Paint in Red is designed for professionals and serious DIYers seeking robust protection for truck and commercial vehicle chassis. Its key benefit is a durable, high-build polyurethane acrylic coating with active corrosion protection, offering a professional semi-gloss finish. A potential caveat is the need for proper ventilation and safety equipment due to its two-component nature and solvent-based formula.
All features
| Colour | Red |
|---|---|
| Model Part Number | FT-PU265-P1.90L-H0.48L-T0.37L-SG-TC |
| Brand | FabioT. |
| Container Volume | 2750ml |
Extended Product Information
FAQs
What is the shelf life of the mixed paint?
The pot life of the mixed 2K paint is typically limited, often between 2-4 hours at 20°C. Always refer to the product's technical data sheet for exact information, as it decreases with higher temperatures.
Can this paint be applied over existing paint?
Yes, it can be applied over existing, sound paintwork provided it is properly prepared (cleaned, degreased, and lightly abraded for adhesion). If the existing paint is in poor condition, it should be removed.
What safety precautions should I take when using this product?
Always use in a well-ventilated area. Wear appropriate personal protective equipment (PPE), including a respirator with organic vapor cartridges, chemical-resistant gloves, and eye protection. Consult the Safety Data Sheet (SDS) for full details.
How long does it take for the chassis paint to be fully cured?
Under standard conditions (e.g., 20°C), the paint will be dust-dry in 15-30 minutes, touch-dry shortly after, but will require 7-8 days for a full chemical and mechanical cure.
Can I use a different brand of hardener or thinner?
It is strongly recommended to use only the FabioT. specified hardener and thinner for this product to ensure proper curing, adhesion, and performance. Using incompatible products can lead to system failure.
What is the coverage rate of this paint?
Coverage varies with application thickness and method. A typical estimate for high-build coatings like this is around 8-10 m² per liter at the recommended dry film thickness. Always consult the product's technical data sheet for precise figures.
Troubleshooting
Paint not drying or curing properly
Ensure correct mixing ratio of paint, hardener, and thinner. Verify ambient temperature and humidity are within the recommended application range. Check if the hardener is expired or contaminated.
Poor adhesion to surface
The surface may not have been adequately prepared (e.g., grease, rust, or old coatings not removed). Ensure the surface is clean, dry, and free from contaminants. Consider using a suitable primer if applying to difficult substrates.
Uneven finish or brush marks
Adjust application technique for brush or spray. Ensure paint is thinned to the correct viscosity for the application method. Avoid overworking the paint.
Runs or sags in the coating
Apply thinner coats rather than one heavy coat. Reduce the amount of thinner if the viscosity is too low. Ensure the application surface is not angled excessively during application.
Pros and Cons
Pros
- Excellent durability and protection for heavy-duty chassis.
- Superior corrosion and weather resistance.
- Fast drying times improve workflow efficiency.
- Professional semi-gloss finish.
- Good adhesion to multiple metal substrates.
Cons
- Requires mixing of two components (paint and hardener) and thinner.
- Needs proper safety equipment and ventilation due to solvent content.
- Full cure takes 7-8 days, requiring careful handling during this period.
- Not suitable for application on non-metallic surfaces without proper primer.
Setup, Compatibility & Care
Setup:
This is a two-component (2K) system requiring precise mixing. The kit includes paint, hardener, and thinner. Always follow the manufacturer's recommended mixing ratios (e.g., 1.90L Paint : 0.48L Hardener : 0.37L Thinner for the 2.75L kit) and stir thoroughly. Allow for a brief induction period as specified by the manufacturer if required. Ensure the application area is clean, dry, and well-ventilated.
Compatibility:
This coating is designed for direct application to steel, galvanised steel, and aluminium. For optimal results and adhesion, surfaces should be properly prepared, free from grease, oil, rust, and old paint. A suitable primer may be required depending on the substrate condition and desired performance.
Care:
Maintain the finish by regular cleaning with mild detergents and water. Avoid abrasive cleaners or solvents that could damage the coating. For any maintenance or recoating, ensure surfaces are clean and properly prepared. Address any chips or scratches promptly to prevent underlying corrosion.