Ft Paints Chassis Paint - 5.50 L Kit - Red
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This 5.50L kit of Ft Paints RT 2K PU265 HS Chassis Topcoat in Red is designed for professionals seeking durable, high-build protection for truck and commercial vehicle chassis. Its key benefit is superior corrosion and weather resistance, featuring an active zinc phosphate reinforcement. A potential caveat is that this is a two-component system requiring accurate mixing of paint, hardener, and thinner.
All features
| Colour | Red |
|---|---|
| Model Part Number | FT-PU265-P3.81L-H0.95L-T0.74L-SG-UC |
| Brand | FT Paints |
| Container Volume | 5500 |
Extended Product Information
FAQs
What is the shelf life of the mixed product?
The pot life of the mixed product is limited. Refer to the product data sheet for specific pot life information, typically ranging from a few hours depending on temperature.
Can this be applied over existing paint?
Yes, provided the existing paint is sound, clean, and properly prepared (e.g., light abrasion or adhesion promoter). Always test on a small area first.
What safety precautions should be taken?
Always wear appropriate personal protective equipment (PPE), including solvent-resistant gloves, eye protection, and a respirator suitable for organic vapors. Ensure adequate ventilation during application and drying.
How long does it take to achieve a full cure?
Under standard conditions (e.g., 20°C), a full cure is typically achieved in 7-8 days. Drying times can be affected by temperature and humidity.
What is the coverage rate?
Coverage rates vary based on application method and surface porosity. Consult the product's technical data sheet for specific coverage information.
Can this product be used on automotive body panels, not just chassis?
While designed for heavy-duty chassis, its properties may lend themselves to other applications requiring high protection. However, it is formulated for industrial use and may not meet the aesthetic requirements for automotive body panels.
What is the temperature resistance rating?
The coating can withstand short-term exposure up to 180°C.
Troubleshooting
Paint is too thick or difficult to apply.
Ensure the correct amount of thinner is added during mixing as per the manufacturer's instructions. Verify ambient temperature and humidity, as these can affect viscosity.
Poor adhesion to the surface.
Verify the surface preparation was adequate. Ensure the substrate (steel, galvanized steel, aluminum) was clean, dry, and free from grease, oil, or rust. Re-prime if necessary.
Uneven or dull finish.
Check for inconsistent application technique or incorrect spray gun settings. Ensure proper mixing of the 2K components and adequate stirring.
Coating remains tacky after extended drying time.
Confirm the correct hardener was used and the mixing ratio was accurate. Check if application occurred in temperatures below the recommended range or if humidity is excessively high.
Pros and Cons
Pros
- Excellent durability for demanding commercial applications.
- Superior protection against rust and corrosion.
- Resistant to UV rays, weather, and solvents.
- Good adhesion to common chassis materials.
- Fast drying times improve workflow efficiency.
Cons
- Requires careful mixing of three components (paint, hardener, thinner).
- Semi-gloss finish may not be suitable for all aesthetic preferences.
- Heat resistance is for short-term exposure only.
- Full cure takes several days, requiring patience before heavy use.
Setup, Compatibility & Care
Setup:
This is a 2K (two-component) system. Accurate mixing is critical. The kit includes 3.81L of paint, 0.95L of hardener, and 0.74L of thinner. Ensure components are thoroughly mixed according to the manufacturer's ratio (refer to product label for exact ratios) before application. Use in a well-ventilated area.
Compatibility:
This topcoat is designed for application over properly prepared steel, galvanized steel, and aluminum surfaces. Ensure surfaces are clean, dry, and free from contaminants. It is compatible with electrostatic, Airmix, Airless, and brush application methods.
Care:
To maintain the protective properties, clean chassis surfaces with mild detergents and water. Avoid abrasive cleaners or solvents that could damage the coating. Regular inspection for any chips or damage is recommended, with prompt touch-ups to prevent underlying corrosion.