Ft Paints Chassis Paint - 5500ml - Yellow
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This guide is for owners and operators of trucks and commercial vehicles needing robust chassis protection. The key benefit is its high-build polyurethane acrylic formula offering superior durability and corrosion resistance. A caveat is the need for proper ventilation and safety equipment due to its solvent-based nature. This 5.50L kit provides a semi-gloss finish with excellent resistance to weather, UV, solvents, and heat, featuring active corrosion protection with zinc phosphate and strong adhesion to various metal surfaces.
All features
| Colour | Yellow |
|---|---|
| Model Part Number | 2K PU265 HS |
| Brand | FT Paints |
| Container Volume | 5500ml |
Extended Product Information
FAQs
What is the shelf life of the unmixed product?
The shelf life of unmixed components is typically 12 months when stored in original, unopened containers in a cool, dry place. Refer to the product packaging for specific expiry dates.
Can this paint be applied in cold temperatures?
Application is best between 15°C and 25°C. Applying in temperatures below 10°C can significantly slow down drying and curing times and may affect film formation. Always refer to the Technical Data Sheet for specific temperature guidelines.
How do I clean my spray equipment after use?
Clean spray equipment immediately after use with a suitable solvent, such as a PU-grade thinner. Refer to the product's Technical Data Sheet for recommended cleaning solvents.
What safety precautions are necessary when using this product?
Always use in a well-ventilated area. Wear appropriate PPE, including a respirator with organic vapor cartridges, chemical-resistant gloves, and eye protection. Avoid contact with skin and eyes.
Can I use a different brand of hardener or thinner?
It is strongly recommended to use only the FT Paints hardener and thinner specified for this product. Using incompatible products can lead to improper curing, poor performance, and coating failure.
What is the pot life of the mixed paint?
The pot life of the mixed product is typically 2-3 hours at 20°C. This time decreases significantly at higher temperatures. Only mix the amount of product that can be applied within this timeframe.
Can I apply this directly over old paint?
Yes, if the old paint is sound, clean, and well-adhered. Lightly abrade the surface to ensure good inter-coat adhesion. If the old paint is of unknown type or in poor condition, it's best to remove it or prime with a compatible system.
Troubleshooting
Paint is too thick or difficult to apply.
Ensure the correct amount of thinner is added according to the mixing instructions and ambient temperature. Stir thoroughly.
Poor adhesion to the surface.
Verify the surface was properly prepared, cleaned, and degreased. Ensure compatibility with the substrate and that any required primers were used.
Uneven finish or "orange peel" effect.
Adjust spray gun settings (pressure, tip size), spray distance, and application speed. Ensure the paint is mixed thoroughly and thinned correctly for the application method.
Runs or drips during application.
Apply thinner coats rather than one heavy coat. Reduce the amount of thinner if the paint is too thin, or check spray gun settings. Allow adequate flash-off time between coats.
Product not drying or curing properly.
Check the mix ratio of paint to hardener. Ensure you are applying within the pot life of the mixed product. Verify ambient temperature and humidity are within recommended application ranges.
Pros and Cons
Pros
- Excellent corrosion and weather resistance for long-term protection.
- High-build formula provides substantial physical protection to the chassis.
- Fast drying times minimize vehicle downtime.
- Suitable for a wide range of metal substrates.
- Professional semi-gloss finish enhances appearance.
Cons
- Requires proper ventilation and safety precautions due to solvent content.
- Two-component (2K) system requires accurate mixing ratios.
- Full cure takes over a week, requiring patience before heavy use.
- Specialized hardener and thinner required, not included in all kits.
Setup, Compatibility & Care
Preparation is Key: Ensure the surface is clean, dry, and free from grease, oil, and existing rust. For best results, prime steel surfaces with a suitable epoxy or polyurethane primer. Ensure compatibility with galvanized steel and aluminum surfaces; light abrasion may be necessary.
Mixing: This is a 2K (two-component) product. The kit includes paint, hardener, and thinner. Refer to the product's Technical Data Sheet (TDS) for the precise mixing ratio of paint to hardener and the recommended amount of thinner based on the application method. Mix thoroughly using a mechanical stirrer until a homogeneous mixture is achieved.
Application: Apply using electrostatic, Airmix, Airless spray, or brush. Ensure adequate ventilation and use appropriate personal protective equipment (PPE), including a respirator, gloves, and eye protection. Apply in thin, even coats. Allow recommended recoat times between layers as per the TDS.
Drying and Curing: The paint will be dust-dry in 15-30 minutes at 20°C. A full, hard cure will take approximately 7-8 days under standard conditions. Avoid exposing the coated surface to heavy stress or cleaning until fully cured.
Care: Clean the chassis regularly with mild detergents and water. Avoid abrasive cleaners or high-pressure washing directly on painted seams. For minor scratches, touch-up may be possible following the same preparation and application guidelines.