Ft Paints Chassis Paint - 1100ml - Grey
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This guide is for professionals and serious DIYers looking to provide heavy-duty, long-lasting protection for truck and commercial vehicle chassis. The key benefit is superior corrosion and weather resistance through a high-build polyurethane acrylic formula reinforced with zinc phosphate. A potential caveat is the need for proper ventilation and personal protective equipment due to its chemical composition and application requirements. This product offers durable protection, a professional semi-gloss finish, and strong adhesion to various metal surfaces, ideal for demanding environments.
All features
| Colour | Grey |
|---|---|
| Model Part Number | 2K PU265 |
| Brand | FT Paints |
| Container Volume | 1100ml |
Extended Product Information
FAQs
What is the mixing ratio for the 1.10L kit?
The 1.10L kit typically contains 0.76L paint, 0.19L hardener, and 0.15L thinner. Always refer to the specific product's Technical Data Sheet (TDS) for the exact mixing ratio and instructions.
How long does it take for the paint to fully cure?
Under standard conditions, the paint will be dust-dry in 15-30 minutes, but a full cure is achieved in approximately 7-8 days.
Can this paint be applied over existing paint?
It can be applied over existing, sound paint systems if they are compatible with 2K polyurethane coatings. Ensure the surface is properly cleaned and abraded. For best results, a primer is often recommended.
What surfaces can I apply this to?
This topcoat bonds well to prepared steel, galvanised steel, and aluminium. It is designed for chassis applications.
Is this paint suitable for use in high-temperature areas?
Yes, it is heat resistant and can withstand short-term exposure up to 180°C, making it suitable for areas near engine or exhaust components.
Do I need special equipment to apply it?
It can be applied via electrostatic, Airmix, Airless sprayers, or with a brush. Ensure appropriate safety equipment and ventilation are used regardless of application method.
What is the finish like?
The product provides a semi-gloss finish, offering a balance between a high-sheen look and a more practical, less reflective surface.
Troubleshooting
Paint not drying or curing properly
Ensure correct mixing ratios of paint, hardener, and thinner. Verify ambient temperature and humidity are within recommended application range. Check that the correct hardener for this specific product has been used.
Poor adhesion to the surface
The surface may not have been adequately prepared. Ensure it was clean, dry, and free of grease, rust, or old coatings. A suitable primer might be necessary for optimal adhesion.
Uneven finish or brush marks
When brush applying, use a high-quality brush and apply thin, even coats. Avoid overworking the paint. For spray application, ensure correct spray gun setup, pressure, and technique. Consider thinning if necessary according to TDS.
Runs or sags in the coating
This usually indicates the application of too much paint in one coat. Apply thinner coats and allow adequate flash-off time between coats. Reduce spray pressure or tip size if spraying.
Pros and Cons
Pros
- Exceptional durability for heavy-duty applications.
- Excellent corrosion and rust prevention.
- Provides a professional, attractive finish.
- Resistant to UV, weather, and solvents.
- Suitable for various metal substrates.
- Handles high temperatures effectively.
Cons
- Requires proper ventilation and PPE for safe application.
- Requires a hardener and thinner (kit bundle), adding complexity.
- Full cure takes 7-8 days, requiring patience for optimal performance.
- Not suitable for all materials; best on bare metal or primed surfaces.
- Can be difficult to apply evenly with brush without practice.
Setup, Compatibility & Care
Setup: This product is a 2K (two-component) system requiring mixing with a specific hardener and thinner. Always refer to the product's Technical Data Sheet (TDS) for precise mixing ratios before application. Ensure the substrate is clean, dry, and free from grease, oil, and contaminants. A suitable primer may be required depending on the substrate and desired performance.
Compatibility: Bonds well to prepared steel, galvanised steel, and aluminium. It is designed as a topcoat for chassis applications and is generally compatible with existing primers if they are suitable for polyurethane systems. Do NOT apply to surfaces treated with silicone or other release agents.
Care: Once fully cured (7-8 days), the coating is durable and requires minimal care beyond standard washing. Avoid abrasive cleaners or high-pressure washing directly on the coated surface for extended periods, as this can eventually degrade the finish. For maintenance, clean with mild detergents and water. Inspect periodically for any signs of damage that may require touch-up.