Ft Paints Chassis Paint - 20000ml - Blue
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This high-build polyurethane acrylic coating is designed for professionals and DIY enthusiasts seeking heavy-duty protection for truck and commercial vehicle chassis. Its key benefit is providing durable, long-lasting defense against corrosion and environmental damage with a professional semi-gloss finish. A potential caveat is the need for proper ventilation and personal protective equipment due to its solvent-based nature. The product offers excellent adhesion, weather resistance, and heat resistance, making it ideal for demanding applications.
All features
| Colour | Blue |
|---|---|
| Model Part Number | 2K PU265 |
| Brand | FabioT. |
| Container Volume | 20000 |
Extended Product Information
FAQs
What is the pot life of the mixed product?
The pot life depends on the temperature and the specific mixing ratio. Refer to the product's technical data sheet for precise information, but typically it ranges from 1-3 hours at 20°C.
Can this be applied over existing paint?
Yes, it can be applied over well-adhered, sound existing paint systems after proper surface preparation and sanding. Ensure compatibility with the existing coating.
What is the recommended film thickness?
The recommended dry film thickness (DFT) per coat is typically between 50-75 microns. The high-build nature allows for achieving thicker films over multiple coats.
How long should I wait between coats?
The recoat interval depends on temperature and humidity. Generally, it is between 4-12 hours at 20°C. Allow for sufficient drying until the surface is tack-free.
Is this product suitable for marine applications?
While it offers excellent weather and corrosion resistance, specific marine-grade coatings might be recommended for constant immersion in saltwater. However, it can provide good protection for components exposed to marine environments.
What safety precautions should I take?
Always use in a well-ventilated area. Wear appropriate personal protective equipment, including a respirator with organic vapor cartridges, chemical-resistant gloves, and eye protection. Consult the Safety Data Sheet (SDS) for detailed safety information.
What is the coverage rate?
The theoretical coverage rate is approximately 8-10 m² per litre at a dry film thickness of 50 microns. This can vary based on the application method and surface porosity.
Troubleshooting
Coating is too thick or difficult to apply
Ensure correct mixing ratios of paint, hardener, and thinner. Adjust thinner amount according to application method and temperature, referring to manufacturer's guidelines.
Poor adhesion to the substrate
Verify that the surface was properly prepared (cleaned, degreased, and abraded). Ensure the substrate is dry and free from rust or old, flaking paint. Check for compatibility with any primer used.
Surface remains tacky or does not cure fully
Check the mixing ratio of the hardener. Ensure the temperature and humidity are within the recommended application range. Insufficient mixing can also lead to incomplete curing.
Runs or sags during application
Reduce the amount of thinner. Apply thinner coats, especially when spraying. Ensure adequate flash-off time between coats if necessary.
Bubbling or blistering of the finish
Ensure the substrate is completely dry before application. Avoid applying in humid conditions or direct sunlight. Ensure proper ventilation during application and curing.
Pros and Cons
Pros
- Provides excellent corrosion protection with zinc phosphate.
- Offers superior resistance to UV, weather, and solvents.
- Achieves a professional semi-gloss finish.
- Suitable for a wide range of application methods.
- Fast drying times improve workflow efficiency.
- Durable and long-lasting protection for heavy-duty vehicles.
Cons
- Requires proper ventilation and personal protective equipment.
- Full cure time of 7-8 days means the vehicle is out of service for a significant period.
- Not suitable for non-metal surfaces.
- Requires a hardener and thinner, adding to the complexity of mixing.
- Higher initial cost compared to single-component coatings.
Setup, Compatibility & Care
Setup:
This is a 2K (two-component) system requiring mixing of paint, hardener, and thinner. Always follow the manufacturer's recommended mixing ratios for optimal performance. Ensure surfaces are clean, dry, and free from contaminants. Abrade surfaces for best adhesion. Apply in a well-ventilated area.
Compatibility:
Suitable for use on steel, galvanised steel, and aluminium. Not recommended for use on plastics or other non-metallic surfaces. Ensure all application equipment is clean and compatible with polyurethane coatings.
Care:
Keep containers tightly sealed when not in use. Store in a cool, dry place away from direct sunlight and sources of ignition. For cleaning application equipment, use appropriate thinners as recommended by the manufacturer. Once cured, the surface can be cleaned with mild detergents and water.