Ft Paints Texture Paint - 100ml - Green - Semi Gloss
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This 100ml sample of FabioT. RT 2K Polyurethane Texture Paint is ideal for professionals and DIY enthusiasts looking to apply a durable, semi-gloss textured finish to industrial machinery, tools, lockers, and steel structures. Its key benefit is providing a tough, decorative coating that hides surface imperfections and offers excellent resistance to impacts, UV, weather, and chemicals. A caveat to consider is that it's a 2K system, requiring proper mixing and ventilation for safe and effective application.
All features
| Colour | Green |
|---|---|
| Model Part Number | FT-PU300-100SAM-S-CV |
| Brand | FabioT. |
| Container Volume | 100ml |
Extended Product Information
FAQs
What is a 2K Polyurethane-Acrylic paint?
A 2K (two-component) paint requires mixing a base component with a hardener. This reaction creates a much more durable, chemical-resistant, and long-lasting finish compared to single-component paints.
How do I mix the paint?
Refer to the product's technical data sheet for the precise mixing ratio of the base paint and hardener. Mix thoroughly to ensure an even distribution of the hardener.
What is the best way to apply this paint?
This paint is suitable for application via spray gun or airless equipment for best results. Ensure proper ventilation and wear protective gear.
How long does it take to dry?
Drying times vary based on temperature, humidity, and film thickness. Typically, it will be touch-dry within a few hours and ready for recoating or light use after 24 hours, with full hardness achieved over several days.
Can I use this paint on wood?
While primarily designed for metal, it can be used on wood if properly primed with a suitable metal primer that is compatible with polyurethane coatings. Ensure the wood surface is stable and prepared.
What is the shelf life of the mixed paint?
Once mixed, the paint has a limited pot life, typically ranging from a few hours to a day, depending on conditions. It must be used within this time frame.
Is this paint suitable for food contact surfaces?
No, this product is not formulated for food contact applications and should not be used where it may come into direct contact with food.
Troubleshooting
Paint not curing or curing slowly
Ensure the correct mixing ratio of base and hardener was used. Verify the temperature is within the recommended application range. Ensure both components were thoroughly mixed.
Poor adhesion to surface
The surface may not have been properly prepared. Ensure it was clean, dry, and free of grease or rust. Consider a light sanding before application.
Uneven or rough texture
Check spray gun settings (pressure, nozzle size) and application technique. Ensure consistent distance from the surface. Stirring the paint thoroughly during application can also help maintain texture.
Runs or sags in the finish
This can be caused by applying the paint too thickly or at too low a pressure. Apply in thinner coats and allow proper flash-off time between coats. Adjust spray equipment for optimal atomization.
Pros and Cons
Pros
- Provides a tough, protective, and decorative textured finish.
- Excellent resistance to impacts, UV rays, weather, chemicals, and solvents.
- Hides surface imperfections effectively.
- High adhesion ensures a durable bond to metal surfaces.
- Suitable for both spray gun and airless equipment.
Cons
- Requires mixing of two components (2K system), demanding careful preparation.
- Ventilation is crucial during application due to chemical composition.
- Sample size (100ml) is suitable for small projects or testing only.
- Requires specific application equipment (spray gun or airless sprayer).
Setup, Compatibility & Care
Setup:
This is a 2K (two-component) product, meaning the hardener must be mixed with the base paint in the correct ratio as specified by the manufacturer before application. Ensure adequate ventilation in the application area. Prepare the surface by cleaning, degreasing, and ensuring it is dry. Light abrasion may be necessary for optimal adhesion on smooth surfaces.
Compatibility:
Primarily designed for metal surfaces, including steel structures, industrial machinery, components, lockers, and tools. It adheres well to properly prepared metal substrates. It is not recommended for use on plastics or wood without appropriate priming.
Care:
Once fully cured, the surface is resistant to water, oil, and many solvents. Cleaning can be done with a damp cloth. For tougher grime, mild detergents can be used. Avoid using abrasive cleaners or solvents that could degrade the finish. Ensure proper ventilation during application and allow for adequate curing time before exposing to harsh conditions.