Siramico Coatings Sepia Brown One Coat - Ultra Heavy Duty Garage Floor Paint - 5 Litres - Brown

Ultra Hard Wearing Formula, Weight: 13.22773572 pounds, Manufacturer: Siramico Coatings

Currently unavailable

Colour

Currently out of stock

This product is not available at the moment. Check back later.

Product Information

Full details

This guide is for homeowners and professionals looking to protect and enhance their garage floors with a durable, easy-to-apply coating. The Siramico Coatings Sepia Brown One Coat offers an ultra-hard-wearing, single-application solution for a robust finish. A potential caveat is ensuring proper surface preparation for optimal adhesion and longevity.

All features

ColourBrown
Model Part NumberSIRAM-GFLOOR
BrandSIRAMICO COATINGS

Extended Product Information

FAQs

Can I apply this over existing paint?

No, this product is designed for bare, properly prepared concrete. Existing paint or sealers must be completely removed before application.

How long does it take to fully cure?

While light foot traffic is possible after 24-48 hours, the coating requires a full 7 days to cure completely before allowing vehicle parking.

What is the coverage rate?

Coverage varies based on the porosity and condition of the concrete. Refer to the product packaging for specific coverage estimates.

Is this product suitable for outdoor use?

This product is specifically formulated for garage floors and is not recommended for outdoor use where it may be exposed to UV rays and weather elements.

How do I clean the coated floor?

Clean with a mild soap and water solution using a soft brush or cloth. Avoid abrasive cleaners or solvents.

What is the weight of the product?

The product weighs approximately 13.23 pounds.

Are there other color options available?

Yes, Siramico Coatings One Coat is available in other colors such as Anthracite Grey, White, Fir Green, and Grey.

Troubleshooting

Paint not adhering properly

Ensure the concrete surface was thoroughly cleaned, degreased, etched, and completely dry before application. Re-prepare the surface if necessary.

Uneven finish or roller marks

Ensure consistent application technique. Work in wet edges and avoid stopping and starting in the middle of a section. Ensure paint is well-mixed.

Bubbling or blistering

This can be caused by moisture in the concrete or applying in excessively high temperatures. Ensure concrete is dry and cure slowly. Avoid direct sunlight during application if possible.

Tackiness after intended drying time

Check environmental conditions (temperature and humidity). Ensure adequate ventilation. High humidity or low temperatures can significantly extend drying times.

Pros and Cons

Pros

  • Single application saves time and labor.
  • Excellent resistance to heavy loads and impacts.
  • Protects against oil, grease, and chemical spills.
  • Provides a professional, durable finish.
  • Available in multiple colors for varied aesthetics.

Cons

  • Requires thorough surface preparation for best results.
  • Adequate ventilation is necessary during application and drying.
  • Drying and curing times can vary based on environmental conditions.
  • May not be suitable for extremely humid environments without specific prep.
  • Not intended for use on surfaces other than concrete.

Setup, Compatibility & Care

Preparation is Crucial:

  1. Ensure the concrete floor is clean, dry, and free from grease, oil, paint, or any loose debris. Use a degreaser and cleaner specifically designed for concrete.
  2. For optimal adhesion, etch the concrete surface using an acid etching solution or by mechanical grinding. Thoroughly rinse and allow the floor to dry completely. A moisture test is recommended.
  3. Repair any cracks or holes in the concrete before application.

Application:

  • Stir the paint thoroughly before and during use.
  • Apply a single, even coat using a high-quality roller or brush. Avoid over-application or leaving puddles.
  • Work in manageable sections to ensure a uniform finish.

Compatibility:

  • This product is specifically designed for bare concrete garage floors.
  • Do not apply over existing painted or sealed surfaces without proper removal or preparation.

Care:

  • Allow the coating to cure fully for at least 7 days before heavy use or vehicle traffic.
  • Clean spills promptly with mild soap and water. Avoid harsh chemical cleaners that could damage the coating.
  • Regular sweeping will help maintain the finish.