Auto Extreme All Purpose Automotive Spray Paint - Clear - 250ml
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This 250ml clear lacquer coat aerosol is designed for DIY enthusiasts and professionals seeking a durable finish for automotive and general-purpose applications. Its key benefit is excellent coverage and adhesion, allowing for quick and easy application with minimal effort. A potential caveat is the need for proper ventilation due to its aerosol nature.
All features
| Colour | White |
|---|---|
| Model Part Number | 1905 |
| Brand | Auto Extreme |
| Container Volume | 250 |
Extended Product Information
FAQs
What surfaces can I use this clear lacquer on?
This clear lacquer is suitable for a variety of surfaces including primed metal, plastic, and wood. Ensure all surfaces are clean and properly prepared before application.
How long does the paint need to dry?
Drying times can vary based on temperature, humidity, and application thickness. Generally, it is touch-dry in about 10-20 minutes, and ready for recoating after 1-2 hours. Full cure can take 24 hours or more.
Do I need to use a primer before applying this clear coat?
While it can adhere to some surfaces directly, using a compatible primer is recommended for optimal adhesion, durability, and a uniform finish, especially on bare metal or plastic.
Can this product be used on car interiors?
Yes, it is suitable for indoor use, but ensure adequate ventilation during application and drying. It's primarily a protective clear coat, so consider its intended finish and durability for interior applications.
How do I prevent the nozzle from clogging?
After each use, turn the can upside down and spray for a few seconds until only clear propellant comes out. This clears the nozzle and prevents paint from drying inside.
What is the coverage area of a 250ml can?
Coverage varies depending on the surface porosity and application thickness, but a 250ml can typically covers approximately 0.5 to 1 square meter (5-10 square feet) with a single coat.
Is this product sandable after it dries?
Yes, once fully cured, the clear lacquer can be wet or dry sanded for further finishing steps, such as compounding and polishing, to achieve a smoother surface.
Troubleshooting
Uneven spray pattern or sputtering
Shake the can more vigorously. Ensure the nozzle is not blocked by inverting the can and spraying briefly to clear it. If the issue persists, the can may be faulty or empty.
Runs or drips in the finish
Applied too thickly or too close to the surface. Allow the paint to dry completely and then gently sand the affected area smooth. Reapply in thinner coats from a greater distance.
Poor adhesion or peeling
Surface was not properly prepared (not clean, dry, or sanded). Ensure thorough cleaning and light sanding of the substrate before application. For best results, use a compatible primer.
Lacquered surface feels sticky after drying
This can occur if applied too thickly or in humid conditions. Ensure adequate ventilation and drying time. If minor tackiness remains, allow more time in a dry environment. For severe cases, the coating may need to be removed and reapplied.
Pros and Cons
Pros
- Provides a protective clear finish.
- Easy to apply with a spray can.
- Good adhesion to various surfaces.
- Suitable for both interior and exterior applications.
- Offers good coverage for efficient use.
Cons
- Requires good ventilation during use.
- Aerosol cans can be difficult to use completely.
- May require surface preparation for optimal adhesion.
- Finish quality can depend on user technique.
Setup, Compatibility & Care
Setup: Ensure the surface to be painted is clean, dry, and free from grease, wax, or rust. Lightly sand glossy surfaces to improve adhesion. Shake the aerosol can vigorously for at least two minutes before use and periodically during application. Hold the can upright and approximately 25-30 cm (10-12 inches) from the surface.
Compatibility: This clear lacquer is suitable for use over most automotive primers and existing paint finishes. It can also be applied to various substrates including metal, plastic, and wood, provided they are properly prepared.
Care: Store the can in a cool, dry place away from direct sunlight and heat sources. After use, invert the can and spray for a few seconds to clear the nozzle and prevent clogging.