Ft Paints 400Ml Spray Can Floor Semi Gloss Paint - Yellow
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This guide is for professionals and DIY enthusiasts looking to create durable, high-performance floor coatings in industrial or heavy-traffic residential settings. The RT 2K Epoxy Floor Paint offers exceptional abrasion and chemical resistance, providing a seamless, semi-gloss finish. A key caveat is the need for proper surface preparation for optimal adhesion.
All features
| Colour | Yellow |
|---|---|
| Model Part Number | FT-EP275-400AER-G-IP |
| Brand | FabioT. |
Extended Product Information
FAQs
What is the best way to prepare concrete for this epoxy paint?
The concrete surface must be clean, dry, and free of any contaminants. Mechanical grinding or acid etching is often recommended to create a profile for optimal adhesion, followed by thorough cleaning.
Can this paint be used on garage floors?
Yes, the RT 2K Epoxy Floor Paint is highly suitable for garage floors due to its resistance to chemicals, oils, and abrasion from vehicle traffic.
How long does it take for the paint to be fully cured?
The paint is walkable in 24 hours and typically achieves full cure within 7 days, though this can vary slightly with temperature and humidity.
Is this product suitable for outdoor use?
While it offers excellent chemical and abrasion resistance, its suitability for outdoor use depends on UV exposure and specific environmental conditions. Consult the manufacturer's detailed technical data sheet for outdoor application guidance.
Can I apply this paint over an existing painted floor?
It is best to apply over bare, prepared concrete. If applying over an existing coating, ensure it is sound, well-adhered, and compatible. A test patch is recommended, or the old coating may need to be removed.
What is the coverage rate of the paint?
Coverage rates vary depending on application thickness and substrate porosity. Refer to the product's technical data sheet for specific coverage estimates per square meter.
Does the product contain solvents?
No, this is a solvent-free 2K epoxy formula, making it safer to use with reduced VOC emissions.
Troubleshooting
Paint not curing or curing slowly
Ensure correct mixing ratios if applicable, check ambient temperature and humidity levels, and verify substrate dryness. Insufficient mixing or application outside recommended conditions can cause slow curing.
Poor adhesion or bubbling
The concrete surface may not have been properly prepared or was contaminated. Ensure the substrate is clean, dry, and free from dust, grease, or previous coatings. Re-prepare the surface if necessary.
Uneven finish or streaks
Ensure consistent application technique, maintain a wet edge, and avoid overworking the material. If using a roller, use a suitable nap length and apply with even pressure.
Aerosol can not spraying properly
Ensure the can is held upright and shaken vigorously before and during use. Check the nozzle for blockages; clear with a fine pin if necessary.
Pros and Cons
Pros
- High resistance to mechanical wear and tear.
- Excellent protection against a wide range of chemicals and oils.
- Durable and long-lasting finish on concrete surfaces.
- Fast return to service with quick curing times.
- Professional semi-gloss aesthetic.
Cons
- Requires thorough surface preparation for optimal performance.
- Application might require specific tools like rollers or trowels.
- Limited to concrete or compatible primed substrates.
- Solvent-free nature means potentially longer initial drying time compared to some solvent-based alternatives.
- Specific temperature and humidity conditions may affect application and curing.
Setup, Compatibility & Care Instructions
Surface Preparation: Ensure the concrete surface is clean, dry, and free from any contaminants such as oil, grease, dust, or old coatings. Acid etching or mechanical grinding may be required for optimal adhesion.
Application:
- Ensure the product is at the correct temperature (refer to manufacturer's specific guidelines if available).
- If applying by roller or trowel, mix components as per the 2K epoxy instructions and apply evenly. For spray application, use the provided aerosol can.
- Maintain consistent application thickness. Overlap passes slightly to ensure a seamless finish.
- For anti-slip properties, incorporate quartz additives during application as recommended.
Compatibility: Compatible with Mipa primers. Designed for application on concrete substrates. Ensure any existing coatings are fully compatible or removed.
Care: Clean spills immediately. Use a damp cloth or a mild detergent for general cleaning. Avoid abrasive cleaners or harsh chemicals that could damage the coating.