WALPLUS Stone Classic Blend 3D Perceiving Sticker Tile DIY Peel and Stick Splashback, Waterproof Backsplash - Green
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This guide is for DIY enthusiasts and renters looking for a quick and stylish way to update kitchen backsplashes or bathroom walls. The key benefit is achieving a decorative, realistic stone look with easy peel-and-stick application. A potential caveat is ensuring the surface is smooth and clean for optimal adhesion. These 30.5 x 30.5 cm green stone-effect stickers offer a waterproof, heat-resistant, and durable solution for a modern update without permanent changes.
All features
| Colour | Green |
|---|---|
| Model Part Number | WT3D3045X5 |
| Brand | Walplus |
Extended Product Information
FAQs
Are these stickers truly waterproof?
Yes, the surface of the stickers is waterproof and heat-resistant, making them suitable for kitchen backsplashes and bathroom walls. However, avoid prolonged direct water exposure or submersion.
Can I use these on my shower walls?
While they are waterproof, they are not designed for constant direct water exposure in shower stalls. They are best suited for areas around sinks or backsplashes where occasional splashes occur.
How do I remove the stickers when I want to change them?
Gently heat the sticker with a hairdryer on a low setting to loosen the adhesive, then slowly peel it away. If any residue remains, clean it with warm, soapy water or a mild adhesive remover.
What size are the stickers?
Each sticker measures approximately 30.5 x 30.5 cm (12 x 12 inches).
Can I apply these over existing tiles?
Yes, as long as the existing tiles are clean, smooth, and the grout lines are not excessively deep or wide. For very uneven surfaces, the outline of the grout may show through.
What is the color of these stickers?
The stickers are green, designed to give a realistic stone effect.
Do I need any special tools to install them?
No special tools are required for basic installation. You may need scissors or a craft knife for cutting to size, and a soft cloth or squeegee to smooth out air bubbles.
Troubleshooting
Stickers are not adhering well
Ensure the surface is thoroughly cleaned, dried, and free from dust or grease. For painted walls, allow sufficient drying time after painting. If the surface is slightly textured, try applying gentle heat with a hairdryer (low setting) while smoothing to improve adhesion.
Air bubbles appearing under the stickers
Slowly peel back the sticker and reapply, smoothing outwards from the center with a soft cloth or squeegee. If the bubble is small and already adhered, you can try gently pricking it with a fine needle and pressing flat.
Difficulty cutting the stickers cleanly
Use a sharp craft knife or a precision cutting tool on a cutting mat for clean, straight lines. Ensure the sticker is flat when cutting.
Removing stickers leaves residue
Gently warm the sticker with a hairdryer on a low setting to soften the adhesive. Peel slowly from a corner. Any remaining residue can typically be removed with a mild adhesive remover or warm soapy water and a soft cloth.
Pros and Cons
Pros
- Easy and quick to install
- Waterproof and heat-resistant for kitchen and bathroom use
- Removable without damaging walls, suitable for renters
- Can be cut for a custom fit
- Provides a decorative and modern aesthetic
- Durable and long-lasting finish
Cons
- Requires a smooth, clean surface for best adhesion
- May not be suitable for heavily textured or uneven walls
- Color may vary slightly from screen representation
- Potential for adhesive residue if removed too quickly or on certain paint finishes
- Only covers 30 pieces, larger areas require multiple packages
Setup, Compatibility & Care
Setup:
- Ensure the surface you intend to cover is clean, dry, and smooth. Remove any dust, grease, or moisture.
- For best results, allow painted walls to cure for at least 2-4 weeks before application.
- Peel the backing paper from one corner of the sticker.
- Carefully align the sticker with your starting point (e.g., a corner of the wall or existing tile) and slowly apply it to the surface, smoothing out any air bubbles as you go.
- If needed, use a sharp craft knife or scissors to cut the stickers for a custom fit around edges or obstacles.
Compatibility:
- Ideal for smooth, painted drywall, plaster, clean tile, or glass surfaces.
- Not recommended for textured, rough, unpainted, or excessively humid walls.
Care:
- Wipe clean with a damp cloth and mild soap if necessary.
- Avoid abrasive cleaners or scrub pads that could damage the surface.
- Ensure no direct, prolonged exposure to water, especially in shower areas.