WRAS Approved Flexible Pipe Connector - Xcel Home - 10mm (M10) x 1/2" BSP - 300mm Long

Not Available WRAS Approved Flexible Pipe Connector - Xcel Home - 10mm (M10) x 1/2" BSP - 300mm Long

WRAS Approved for Compliance and Safety: This flexible pipe connector is WRAS approved, meaning it...

Currently unavailable

Currently out of stock

This product is not available at the moment. Check back later.

Product Information

Full details

This WRAS Approved Flexible Pipe Connector from Xcel Home is designed for plumbing professionals and DIY enthusiasts needing a reliable and safe connection for kitchen and bathroom taps. Its key benefit is ensuring compliance with UK water regulations and providing durable, kink-resistant performance thanks to its stainless steel braided construction. A potential caveat for some users might be the specific M10 fitting, which requires confirmation for compatibility with existing setups.

All features

Brand	Xcel Home

Extended Product Information

FAQs

What does WRAS approved mean?

WRAS approval means the product has been rigorously tested and meets the high standards set by the Water Regulations Advisory Scheme for the UK, ensuring it is safe for use with drinking water and compliant with water supply regulations.

Is this connector suitable for hot and cold water?

Yes, this flexible pipe connector is designed for use with both hot and cold water supplies in domestic plumbing.

Can I use this with any tap?

This connector is compatible with taps featuring a 10mm (M10) inlet. You will also need a 1/2" BSP fitting on your water supply line. Always check your tap's specifications before purchasing.

How long will this connector last?

The durable stainless steel braided construction is designed for long-term reliability and resistance to wear, corrosion, and kinks under normal operating conditions.

What is the inner diameter of the pipe?

The inner bore of this flexible pipe connector is 9mm, designed to ensure efficient water flow and consistent pressure.

Can I cut this hose to a shorter length?

These flexible connectors are not designed to be cut. Cutting the braided hose could compromise its integrity and lead to leaks. It is best to use the provided 300mm length or select a different length if required.

Troubleshooting

Leak at the connection

Check if the connection is hand-tightened sufficiently and then gently tightened with a wrench. Ensure any seals or washers are correctly seated. Re-seat and tighten if necessary, avoiding overtightening.

Low water pressure

Ensure the connector is not kinked. Check that the inner bore (9mm) is not obstructed. Verify that both ends are fully open and that the issue is not with the tap itself or the main water supply.

Connector won't screw on properly

Verify that you are using the correct fittings (10mm M10 and 1/2" BSP). Check for any damage to the threads on either the connector or the tap/valve. Ensure alignment is correct to prevent cross-threading.

Pros and Cons

Pros

Guaranteed safety and compliance with WRAS approval.
Robust and durable construction for long-term reliability.
Easy installation due to flexible design and standard fittings.
Promotes consistent water pressure and efficient flow.
Suitable for both professional and DIY plumbing projects.

Cons

Requires specific 10mm (M10) connection on one end, check compatibility.
300mm length may be too long or too short for some niche installations.
Stainless steel braiding, while durable, can be stiff for very tight spaces.

Setup, Compatibility & Care

Setup:

Ensure the water supply is turned off at the mains.
Disconnect the old pipe connector, if applicable.
Screw the 1/2" BSP end of the connector onto the water supply valve or fitting. Hand-tighten first, then use a wrench for a secure fit (avoid overtightening).
Screw the 10mm (M10) end of the connector onto the tap's inlet. Ensure it is properly aligned to avoid cross-threading.
Hand-tighten and then use a wrench for a secure fit.
Once both ends are securely connected, turn the water supply back on slowly and check for any leaks.

Compatibility:

This connector is designed with a 10mm (M10) connection on one end and a standard 1/2" BSP connection on the other. Verify that your tap has a 10mm (M10) inlet and your plumbing system uses a 1/2" BSP fitting before purchase.

Care:

Periodically check the connector for any signs of wear, damage, or leaks.
Clean the exterior with a damp cloth; avoid abrasive cleaners.
Ensure connections remain tight but do not overtighten, as this can damage the fittings or the connector.