Silverhook Big Boy Lightweight Easy Sanding Car Body Filler with Hardener & Applicator - 250ml
Silverhook Lightweight Body Filler is a polyester filler that offers easy application and excellen...Silverhook Lightweight Body Filler is a polyester filler that offers easy application and excellent sanding properties even after leaving overnight. It is a two-component putty for application on large surfaces and is characterised by high elasticity and gripping ability to a wide range of surfaces. The lightweight filler is talc-free and sands to a smooth finish. Silverhook Lightweight Body Filler will not clog up abrasive paper while sanding. It can also be used as a general-purpose filler on wood, metal, and rigid plastics. As the filler is corrosion resistant, it makes a perfect exterior filler on areas requiring a paint finish eg. window frames, walls, etc. Bridging compound that has strong bonding qualities to repair wood, metal, concrete and some PVC. Ideal for use on large areas and is corrosion and water resistant. Contents include: filler, hardener and applicator.
This guide is for anyone using Silverhook Big Boy Lightweight Body Filler to repair and smooth surfaces on cars, wood, metal, or rigid plastics. The key benefit is its easy application and excellent sanding properties, saving you time and effort. However, note that proper surface preparation is crucial for optimal results.
All features
Model Part Number
BIG01
Brand
Silverhook
Extended Product Information
FAQs
How long does the filler take to dry?
The filler typically dries overnight, but always refer to the manufacturer's instructions for the specific drying time, which depends on temperature and humidity.
Can I use this filler on plastic?
Yes, it is suitable for use on rigid plastics. However, ensure the plastic surface is properly prepared.
What kind of sandpaper should I use?
Use a range of sandpaper grits, starting with a coarser grit to remove excess filler and then progressing to finer grits for a smooth finish.
Can I use this filler on exterior surfaces?
Yes, it's corrosion resistant and suitable for exterior use. Ensure it's fully cured before painting.
How should I store the filler?
Store in a cool, dry place, away from direct sunlight and heat, with the lid tightly sealed.
What safety precautions should I take?
Wear appropriate safety equipment, including gloves and eye protection. Work in a well-ventilated area, and avoid inhaling dust during sanding.
How do I remove the filler if I make a mistake?
Once cured, the filler can be removed by sanding. If it's not cured, it can be removed with a scraper before it hardens.
Troubleshooting
Filler is not hardening.
Ensure you have mixed the filler and hardener in the correct ratio. Check the expiry date and ensure the products are not too old. The ambient temperature may be too low, allowing more time for curing.
Filler is difficult to sand.
Allow the filler to cure for the recommended time. Use appropriate sandpaper grit for the job.
Filler shrinks after drying.
Apply the filler in thin layers, allowing each layer to dry before applying the next. Avoid overfilling in one go.
Filler does not adhere properly.
Ensure the surface is clean, dry, and properly prepared with adequate sanding. Use an appropriate primer before painting.
Pros and Cons
Pros
Easy to apply and work with.
Sands to a smooth finish effortlessly.
Suitable for a variety of materials.
Corrosion-resistant for exterior use.
Provides strong bonding qualities.
Comes with all necessary components.
Cons
Requires proper surface preparation for optimal adhesion.
Mixing ratio must be followed accurately for best results.
Limited working time after mixing.
May require multiple applications for deep imperfections.
Storage in a cool, dry place is necessary.
Setup, Compatibility & Care
Setup:
Preparation: Ensure the surface is clean, dry, and free from rust or loose particles. Sand the area to provide a good key for the filler.
Mixing: Mix the filler with the hardener, following the recommended ratio (refer to the product label). Mix thoroughly until the mixture is uniform in colour.
Application: Apply the mixture to the damaged area using the included applicator or a suitable spreader.
Curing: Allow the filler to cure completely according to the manufacturer's instructions, typically overnight, before sanding.
Compatibility:
Materials: Compatible with wood, metal, concrete, and some rigid plastics.
Paints: Can be painted over once fully cured. Use paints suitable for the material.
Care:
Store in a cool, dry place away from direct sunlight.
Keep the container tightly sealed when not in use.
Avoid contact with skin and eyes. Wear appropriate safety equipment (gloves, eye protection) during application and sanding.
Dispose of waste materials properly in accordance with local regulations.
eBay£8.89Visit shop 
B&Q£9.59Visit shop 
