Shopping.co.uk

Plumbright Push-Fit Male Connector - 10mm x 1/2 inch BSP

Plumbright Push-Fit Male Connector - 10mm x 1/2 inch BSP

The Plumbright 10mm x 1/2 inch BSP Male Connector combines the convenience of push-fit technology ...

Best current price£5.44from City Plumbing GB

Best offers

Shopping.co.uk recommended and popular offers

Lowest priceMost popular
City Plumbing GB£5.44Visit shop

Plumbright Men's 10Mm X 1/2" Bsp Brass Connector Dzr Sbmc6714m

Visit shop

One Offer

1 offer from £5.44

View price history by clicking the chart icon.

City Plumbing GBPlumbright Men's 10Mm X 1/2" Bsp Brass Connector Dzr Sbmc6714m
Free delivery in 1–3 days
£5.44
Visit shop

Product Information

Full details

The Plumbright 10mm x 1/2 inch BSP Male Connector is an essential component for professional plumbers and DIY enthusiasts who require a fast, reliable, and secure connection between 10mm pipework and 1/2 inch BSP threaded fittings. Offering the convenience of push-fit installation alongside the structural integrity of DZR brass, this connector significantly reduces project labor times compared to traditional soldering techniques. While it provides a robust, KITEMARK approved seal, users should note that the white plastic finish, while aesthetically clean, requires careful handling during installation to avoid surface scratches or damage to the locking mechanism.

All features

Model Part NumberSBMC6714M
BrandPlumbright

Extended Product Information

FAQs

Is this connector suitable for gas installations?

No, this connector is designed for water systems only and must never be used for gas piping.

Can I use this with copper and plastic pipe?

Yes, it is compatible with most standard 10mm copper and plastic pipework.

Is the white plastic finish paintable?

While the surface can be painted, it is generally intended to be left as is for a clean, visible finish.

What does BSP stand for?

BSP stands for British Standard Pipe, which is the standard thread type used in UK plumbing.

Can these be reused?

Push-fit connectors are generally intended for permanent installations. While technically removable, it is recommended to use a new fitting if you suspect the internal seal or teeth have been damaged.

Does it require PTFE tape?

The push-fit end seals via an internal O-ring. PTFE tape should only be used on the 1/2 inch BSP male thread connection if required by the mating female fitting.

Troubleshooting

Leakage at the pipe insertion point

Remove the pipe, check for scratches on the pipe surface, ensure it was cut square, and re-insert firmly.

Pipe will not insert into the fitting

Check that the pipe is exactly 10mm and that there are no internal obstructions or bent teeth on the internal grab ring.

Difficulty removing the fitting

Use a proper collet release tool designed for push-fit fittings to depress the internal ring before pulling the pipe away.

Pros and Cons

Pros

  • Significantly faster installation compared to soldered fittings
  • No open flames or hot work permits required
  • WRAS and KITEMARK certified for peace of mind
  • Compatible with a wide range of standard 10mm piping
  • Compact design ideal for tight installation spaces

Cons

  • Outer white plastic may show signs of wear if handled roughly
  • Not intended for use with non-standard pipe diameters
  • Requires proper pipe preparation to ensure a watertight seal

Setup, Compatibility & Care

  1. Preparation: Cut the 10mm pipe squarely and remove any burrs or sharp edges using a file.
  2. Clean: Ensure the pipe surface is clean and free of paint or debris before insertion.
  3. Insertion: Push the pipe firmly into the connector until you feel the internal grab ring engage and the pipe 'seat' fully.
  4. Test: Always perform a pressure test on the system before concealing the fitting or closing the wall.
  5. Care: Avoid using aggressive chemical solvents or abrasive cleaners on the white plastic exterior, as this can degrade the material. Simply wipe clean with a damp, soft cloth.

Price History

DatePrice
Visit shop