Home Range Waste Pipe Adapter - Solvent Weld Reducer - White Plastic
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This Home Range solvent weld reducer is designed for plumbers and DIY enthusiasts needing to connect a 36mm waste pipe into a 43mm waste pipe system. It offers a neat, permanent, and leak-resistant joint using solvent cement, ensuring reliability in domestic and commercial plastic waste plumbing. While it provides a robust connection, ensure proper ventilation and safety when using solvent cement.
All features
| Model Part Number | 5056866127608 |
|---|---|
| Brand | Home Range |
Extended Product Information
FAQs
What type of solvent cement should I use with this adapter?
Use a solvent cement specifically formulated for PVC or ABS plastic waste pipes, as recommended by the pipe and fitting manufacturers. Always follow the cement manufacturer's instructions for application and curing times.
Can this adapter be used for hot water waste pipes?
This adapter is designed for standard domestic and commercial cold water waste systems. For applications involving high temperatures, consult specific product guidelines or a professional plumber.
How long does the joint take to cure?
Curing times vary depending on the solvent cement used, temperature, and humidity. Refer to the solvent cement manufacturer's instructions. Typically, joints require at least 24 hours for full cure before being put into service.
What is the purpose of the chamfer on the pipe end?
Chamfering the pipe edge slightly makes it easier to insert the pipe into the fitting socket without damaging the fitting's internal seal or scraping off the solvent cement.
Can I use this adapter with push-fit waste pipes?
No, this adapter is exclusively for solvent weld connections. It is not compatible with push-fit or compression plumbing systems.
What are the dimensions of the adapter?
The adapter reduces from a 43mm pipe connection to a 36mm pipe connection.
Troubleshooting
Joint leaks after installation
This usually indicates insufficient or uneven application of solvent cement, or the pipe was not fully inserted. The joint cannot be re-worked once cured. For a permanent repair, the section of pipe and fitting will need to be cut out and replaced.
Pipe does not fully insert into the fitting
Check that the pipe end is cut squarely and is not deformed. Ensure no internal obstructions exist within the fitting socket. Trim the pipe if necessary.
Solvent cement will not bond the joint
Ensure the correct type of solvent cement for plastic waste pipes is being used. Verify that both the pipe and fitting surfaces are clean and dry before applying cement.
Pros and Cons
Pros
- Creates a strong and permanent joint.
- Leak-resistant connection when installed correctly.
- Suitable for a wide range of domestic and commercial applications.
- Easy to use with standard solvent weld techniques.
- Durable white plastic construction.
Cons
- Requires the use of solvent cement, which needs careful handling and ventilation.
- Permanent joint means it cannot be easily disassembled.
- Only compatible with solvent weld systems, not push-fit or compression fittings.
- Installation requires precise cutting and preparation of pipe ends.
Setup, Compatibility & Care
Setup:
- Ensure both the 43mm pipe end and the 36mm pipe end are clean, dry, and free from burrs or damage. Cut pipes squarely for a proper fit.
- Lightly chamfer the edges of the pipes to be joined.
- Apply an even coat of appropriate solvent cement to the outside of the 36mm pipe and the inside of the 43mm fitting socket intended for the 36mm pipe.
- Immediately push the pipe into the fitting with a slight twisting motion until it bottoms out. Hold for 30 seconds to prevent push-out.
- Wipe away any excess cement with a clean cloth.
- Allow the joint to cure for the time recommended by the solvent cement manufacturer before subjecting it to water flow or pressure.
Compatibility:
- Compatible with standard 43mm and 36mm plastic solvent weld waste pipes.
- Use only with solvent cements specifically designed for plastic plumbing pipes.
- Not compatible with push-fit or compression fittings.
Care:
- This fitting is designed for waste water applications and requires no special maintenance. Ensure the connected waste pipe system is kept clear of debris to maintain optimal performance.