Shopping.co.uk

KLEIN TOOLS VDV501851 Cable Tester Kit - Scout Pro 3 Tester

Not AvailableKLEIN TOOLS VDV501851 Cable Tester Kit - Scout Pro 3 Tester
Not Available

The Scout® Pro 3 Tester Starter Kit is a versatile cable tester that locates and tests voice, data...

Currently unavailable

Currently out of stock

This product is not available at the moment. Check back later.

Product Information

Full details

The KLEIN TOOLS VDV501851 Scout® Pro 3 Tester Starter Kit is designed for network technicians and installers who need to accurately test and locate voice, data, and video cables. Its key benefit is simplifying complex cable installations by identifying multiple cable runs and verifying accuracy, saving time and reducing errors. A potential caveat is that the tone generator functionality requires a separate tracing probe. This comprehensive kit includes a main tester, location mapping remotes for both data and coax cables, and essential adapters for versatile use.

All features

Model Part NumberVDV501-851
BrandKLEIN TOOLS

Extended Product Information

FAQs

What types of cables can the Scout® Pro 3 tester test?

It can test voice (RJ11/12), data (RJ45) and video (coax F-connector) terminated cables, including UTP/STP CAT3 through CAT7 and Coaxial RG59, RG6/6Q.

Does this kit include everything needed to test coax cables?

Yes, the starter kit includes (5) CoaxMap™ F-connector locator remotes and (1) coax F-connector adapter, allowing you to test and map coax cable runs.

How do I identify which cable run goes to which location?

Connect one of the included LanMap™ or CoaxMap™ remotes to the end of each cable at its destination. Then, test from the source using the Scout® Pro 3 tester. The tester will identify each numbered remote, mapping the cable run.

Can the tester measure cable length?

Yes, the Scout® Pro 3 tester can measure cable length accurately up to 2000 feet (610 m).

What is the purpose of the 'Hub Blink' mode?

Hub Blink mode helps you identify the specific port on a hub or switch that a connected cable is plugged into. This is useful for tracing and managing network connections.

Does the tone generator work out of the box?

The tester has a built-in tone generator, but to use it for tracing cables, you need to purchase the analog tracing probe (Cat. No. VDV500-123) separately.

How long does the battery last?

The 9V alkaline battery provides approximately 50 hours of active use.

What should I do if the tester shows a 'Miswire' fault?

A 'Miswire' fault indicates that the cable's conductors are not terminated in the correct order according to the standard wiring scheme (e.g., T568A or T568B for data cables). You will need to re-terminate the cable ends to correct the wiring order.

Troubleshooting

Tester does not power on.

Ensure a fresh 9V battery is correctly installed with proper polarity. Check the battery contacts for dirt or corrosion.

Inaccurate cable length readings.

Verify that the cable is fully plugged into the tester and remote. Ensure the cable type is compatible and the test is performed without other active network equipment connected.

Remote locators are not responding.

Confirm that the remote is properly connected to the cable end. Check the battery in the remote if it has one (though the included ones are passive). Ensure the main tester is powered on and functioning.

Fault detected as 'Open' but cable appears connected.

Check for a broken conductor within the cable. Inspect the termination points (both at the tester and the remote) for loose wires or poor connections.

Difficulty distinguishing cable runs with tone generator.

Ensure you are using the correct tracing probe and that it is compatible with the tester. Move the probe slowly along the cable bundles to pick up the signal. Consider using a different tone style if available.

Pros and Cons

Pros

  • Versatile testing for voice, data, and video cables.
  • Accurate cable length measurement up to 2000 feet.
  • Includes multiple location remotes for efficient cable identification.
  • Backlit display for use in various lighting conditions.
  • Detects a wide range of common cable faults.

Cons

  • Tone generation requires a separately purchased tracing probe.
  • Requires a 9V battery, which is included but is a consumable item.
  • The device itself does not provide PoE (Power over Ethernet) testing.

Setup, Compatibility & Care

Setup:

  1. Install Battery: Open the battery compartment on the back of the tester and insert the included 9V alkaline battery, observing correct polarity.
  2. Connect Cable: Connect the cable to be tested to the appropriate port on the Scout® Pro 3 tester (RJ11, RJ45, or F-connector).
  3. Use Remotes: For location mapping and testing multiple runs, connect the appropriate LanMap™ (RJ45) or CoaxMap™ (F-connector) remote to the other end of the cable.
  4. Power On: Press the 'Test' button to initiate a test.

Compatibility:

  • Cable Types: Supports Shielded or Unshielded Twisted Pair (UTP/STP) cables including CAT3, CAT5E, CAT6, CAT6A, CAT7. Also supports Coaxial cables RG59, RG6/6Q.
  • Connectors: RJ11, RJ12, RJ45, and Coax F-connector.
  • Tone Generator: Requires a separate analog tracing probe (Cat. No. VDV500-123) for tone generation.

Care:

  • Cleaning: Clean the tester and accessories with a soft, dry cloth. Avoid using liquids or harsh chemicals.
  • Storage: Store the kit in its original case or a protective bag when not in use to prevent damage and keep components organized.
  • Battery Replacement: The low battery indicator will illuminate when the battery needs replacement. Use a fresh 9V alkaline battery for optimal performance.
  • Avoid Water/Moisture: This device is not waterproof. Keep it away from water and excessive moisture.