Integral LED Square Evofire IP65 Fire Rated Downlight Satin in Nickel
* Can-less design that provides better airflow, enabling LED lamps to run cooler and prolong life....* Can-less design that provides better airflow, enabling LED lamps to run cooler and prolong life.
* Ultra-thin 1mm bezel
* Fire-resistant glass protection
* Complies to Building Regulations parts B, C,E and L
* Solid Timber 30-60-90min, I-Joist 30-60min
* Screwless push-fit terminals and block
* LED GU10 lamps only max 10W (not included)
* Diameter 85mm, depth 38mm, cut out 70mm
* 30/60/90min Fire-rated Integral Classic GU10 Lamp 4W Warm white 345lm 10 pack (code 69071) Integral Classic GU10 Lamp 4W Cool white 360lm 10 pack (code 21145) Integral Classic GU10 Lamp 4W Daylight 360m 10 pack (code 27760) Integral Classic GU10 Dimmable Lamp 4W Warm white 345lm 10 pack (code 61758) Integral Classic GU10 Dimmable Lamp 4W Cool white 380lm 10 pack (code 88497) Integral Classic GU10 Dimmable Lamp 4W Daylight 380m 10 pack (code 50682) Integral LED Square Evofire IP65 Fire Rated Downlight Satin in Nickel
EvoFire downlights from Integral LED are a new generation of GU10 fire rated downlights. They offer complete fire protection are open rated to allow airflow and are available in insulation coverable versions.
This guide is for homeowners and contractors looking to install the Integral LED Square Evofire IP65 Fire Rated Downlight. The key benefit is its fire protection and open rating, allowing for better airflow and compatibility with various building regulations. However, please note that the GU10 lamps are not included and need to be purchased separately. This guide will help you understand the features, setup, and maintenance of this downlight.
All features
Colour
White
Brand
Integral LED
Extended Product Information
FAQs
What type of lamps can I use?
You can use GU10 LED lamps with a maximum of 10W. The lamps are not included.
Is this downlight fire-rated?
Yes, it is fire-rated, offering complete fire protection and complying with various building regulations.
What is the cutout size?
The cutout size required is 70mm.
Can I use this downlight with a dimmer?
Yes, but ensure the GU10 lamp you use is dimmable and that the dimmer switch is compatible with LED lamps.
What materials can this downlight be installed in?
It is suitable for Solid Timber (30-60-90min) and I-Joist (30-60min).
Is the downlight suitable for bathrooms?
The IP65 rating suggests suitability; however, always consult local regulations and electrical codes for bathroom installations to ensure compliance.
Where can I purchase replacement lamps?
Replacement GU10 LED lamps can be purchased from most electrical suppliers and online retailers.
Troubleshooting
Downlight doesn't turn on.
Check the GU10 lamp is correctly installed and that the power supply is connected. Check circuit breaker.
Lamp flickers or dims.
Ensure the LED lamp is compatible with the downlight and is properly seated. If using a dimmer, verify the dimmer compatibility.
Downlight is too hot.
Ensure the correct wattage LED lamp is used (max 10W). Check for any obstructions blocking airflow.
Pros and Cons
Pros
Fire-rated for enhanced safety.
Open rated design extends LED lamp life.
Easy to install with push-fit terminals.
Sleek, modern design with an ultra-thin bezel.
Complies with various building regulations.
Cons
GU10 lamps are not included and must be purchased separately.
Requires compatible GU10 LED lamps (max 10W).
May require professional installation depending on your experience.
Limited to specific GU10 lamp types.
IP65 rating might not be necessary for all indoor applications.
Setup, Compatibility & Care
Installation:
Ensure the power is turned off before starting.
Cut a 70mm hole for the downlight.
Connect the wiring using the screwless push-fit terminals.
Insert the downlight into the hole.
Compatibility:
Compatible with GU10 LED lamps only (max 10W).
Suitable for Solid Timber (30-60-90min) and I-Joist (30-60min) applications.
Complies with Building Regulations parts B, C, E, and L.