Davant Solvent Weld Swept Tee - 92.5 Degrees - 32mm - Black
Best current price£6.36from B&Q
Best offers
Shopping.co.uk recommended and popular offers
B&Q£6.36Visit shop - Davant 92.5 Degrees Solvent Weld Swept Tee Black (32mm)
Visit shopB&Q£6.36Visit shop All Offers
3 offers from £6.36 - £7.00
View price history by clicking the chart icon.
B&Q - Davant 92.5 Degrees Solvent Weld Swept Tee Black (32mm)
Free delivery in 1–3 days
£6.36
Visit shop
OnBuy.comDavant 92.5 Degrees Solvent Weld Swept Tee 5063884893057
Free delivery in 1–3 days
£6.59
Visit shop
DebenhamsDavant Unisex Black 92.5 Degrees Solvent Weld Swept Tee In
Free delivery in 1–3 days
£7.00
Visit shop
Product Information
Full details
The Davant Solvent Weld Swept Tee (32mm) is an essential plumbing component for professional contractors and DIY enthusiasts tasked with creating secure, leakproof 92.5-degree branches in waste water systems. It offers excellent durability and a sleek black finish, though users should note that it requires solvent cement for installation and is specifically designed for 32mm pipework rather than high-pressure supply lines.
All features
| Model Part Number | 92.5 |
|---|---|
| Brand | Davant |
Extended Product Information
FAQs
Can I use this tee with 40mm pipes?
No, this component is specifically sized for 32mm pipe. Using it with 40mm pipe will result in an improper fit and leaks.
Is this product suitable for hot water discharge?
Yes, it is suitable for standard domestic hot water discharge from sinks and basins, but not for continuous boiling water or industrial chemical processes.
Do I need any special tools for installation?
You will need a hacksaw to cut the pipe, a file for deburring, and specific solvent weld cement for PVC/ABS waste systems.
Can this be painted to match a wall?
While the black finish is durable, you can lightly sand the exterior and apply a plastic-compatible primer and paint if needed.
Is this tee suitable for underground drainage?
No, this component is intended for internal above-ground waste water systems only.
What is the benefit of a swept tee over a standard tee?
A swept tee improves flow characteristics, reducing turbulence and the accumulation of waste materials compared to a sharp 90-degree junction.
Troubleshooting
Joint is leaking immediately after installation
The solvent weld may have been applied unevenly. Ensure surfaces were cleaned of debris and enough adhesive was used to create a full seal.
Pipe will not slide into the tee
Check if the pipe end has burrs from cutting. Use sandpaper or a deburring tool to smooth the end of the pipe before re-applying solvent.
Pros and Cons
Pros
- Permanent, leakproof connection
- Smooth internal bore reduces risk of blockages
- Durable, long-lasting construction
- Easy to integrate into existing 32mm black waste pipe systems
- Professional aesthetic for visible areas
Cons
- Requires solvent welding (no mechanical adjustment)
- Not suitable for high-pressure water systems
- Cannot be easily disassembled once bonded
- Requires specific solvent weld adhesive
Setup, Compatibility & Care
To install the Davant Solvent Weld Swept Tee, ensure all pipe ends are cut square and deburred using a file or sandpaper. Clean the surfaces to be joined with a pipe cleaner to remove dust or grease. Apply an even layer of solvent cement to both the tee socket and the pipe exterior, then push the components together with a slight quarter-turn to ensure complete coverage. Hold for 30 seconds to allow the initial bond to set.
Compatibility: This component is designed exclusively for 32mm rigid waste pipe. It should not be used with flexible or corrugated piping. For maintenance, ensure that the joint is fully cured (typically 24 hours) before subjecting the system to high-volume water flow.