Universal Chainsaw 12" Guide Bar and 2 Chains - Ufixt - A074
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This Ufixt A074 12" guide bar and chain combination pack is designed for chainsaw users needing a reliable replacement or spare set. It offers the convenience of two chains with a single guide bar, providing extended use and value. A potential caveat is the specific chain specification, which must match your chainsaw's requirements.
All features
| Model Part Number | A074 |
|---|---|
| Brand | Ufixt |
Extended Product Information
FAQs
What size chain pitch and gauge does this set use?
This set uses a 3/8" low-profile (LP) pitch and a .050" gauge chain.
How many drive links are on each chain?
Each chain has 44 drive links.
Is this guide bar and chain set compatible with all Stihl chainsaws?
It is compatible with Stihl models that are designed for a 12" bar and use a 3/8" LP, .050" gauge chain with 44 drive links. Always verify your specific model's requirements.
Can I use this set on a brand not listed in the description?
While it's compatible with the listed brands (Alpina, Castel, Efco, Oleomac, Stiga, Stihl), compatibility ultimately depends on whether your chainsaw can accept the specific guide bar length and chain specifications (3/8" LP, .050", 44 drive links).
What is the weight of this product?
The product weighs approximately 1kg.
How often should I replace the chain?
Chains should be replaced when they become excessively worn, stretched, or damaged, or when they can no longer be effectively sharpened. The presence of a second chain allows for immediate replacement when one chain's performance degrades.
Does this kit include bar and chain oil?
No, this kit includes the guide bar and chains only. Bar and chain oil must be purchased separately and used regularly for proper lubrication.
Troubleshooting
Chain not cutting efficiently
Ensure the chain is properly tensioned and sharp. Check for any obstructions or damage to the chain or guide bar.
Chain is too loose or too tight
Readjust the chain tension. A properly tensioned chain should be snug against the bar but still movable by hand with gloves. It should not sag.
Guide bar groove filled with debris
Turn off the chainsaw. Remove the chain and bar and clean the bar groove thoroughly with a brush or compressed air. Ensure the oil hole is clear.
Chain falls off the guide bar
Check chain tension and ensure it is not excessively loose. Verify the guide bar is correctly installed and that the chain and bar are not damaged or warped. Ensure the sprocket is not worn.
Pros and Cons
Pros
- Includes two chains for convenience and extended use.
- Wide compatibility across several popular chainsaw brands.
- Offers good value as a combination pack.
- Standard 12" bar length suitable for many common tasks.
- Direct replacement for Oregon A074, simplifying selection.
Cons
- Requires precise matching of chain specification (3/8 - 050 LP, 44 drive links) to chainsaw model.
- May not be suitable for heavy-duty or professional-grade chainsaws requiring longer or different spec bars.
- Weight of 1kg might be a consideration for some users.
- Specific brand compatibility needs verification for less common models.
Setup, Compatibility & Care
Setup: Before installation, ensure your chainsaw is turned off and the chain brake is engaged. Remove the chain cover. Loosen the guide bar nuts and adjust the chain tensioning screw to allow the guide bar to move freely. Mount the new guide bar, ensuring the drive links of the chain sit correctly in the bar groove. Install the new chain, placing the drive links onto the sprocket and over the guide bar. Reinstall the chain cover and tighten the guide bar nuts. Adjust the chain tension by turning the tensioning screw until the chain is snug but can still be pulled around the bar by hand with gloves. It should not sag, but it also shouldn't bind.
Compatibility: Verify that your chainsaw model is designed to accept a 12" guide bar and specifically uses a 3/8" low-profile pitch chain with a .050" gauge and 44 drive links. Check your chainsaw's manual or existing bar and chain for these specifications. This set is confirmed to replace Oregon A074 and is compatible with Alpina, Castel, Efco, Oleomac, Stiga, and Stihl chainsaws that meet these specifications.
Care: Keep the guide bar groove clean by removing sawdust and debris after each use. Lubricate the chain regularly with bar and chain oil. Check chain tension frequently, as chains can stretch during use. Sharpen chains regularly to maintain cutting efficiency and reduce strain on the engine and bar. Store chains in a dry place, lightly oiled, to prevent rust.