Sanding Belts - 10 Pack - 100mm x 620mm - 80 Grit - Aluminium Oxide
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This 10-pack of 100mm x 620mm sanding belts, featuring 80-grit aluminium oxide construction, is designed for woodworking professionals and DIY enthusiasts using portable belt sanders. The key benefit is achieving smooth, consistent finishes efficiently due to the durable resin bond. A potential caveat is ensuring the 100mm x 620mm size is compatible with your specific machine model.
All features
| Model Part Number | ys11844 |
|---|---|
| Brand | Loops |
Extended Product Information
FAQs
What type of wood is this 80-grit belt best suited for?
This 80-grit belt is effective on a wide variety of woods, including hardwoods like oak and maple, and softwoods like pine. It's particularly useful for initial shaping and smoothing of rough-sawn lumber or preparing surfaces for finer sanding.
How do I know when to replace a sanding belt?
Replace the belt when you notice a significant decrease in its cutting power, if it starts making excessive noise, begins to tear, or if you're getting burn marks or uneven finishes despite proper technique.
Can I use these belts on metal or plastic?
These sanding belts are specifically designed for wood. Using them on metal or plastic may lead to premature clogging, reduced effectiveness, and potential damage to the belt or workpiece.
What is the benefit of an aluminium oxide resin bond?
Aluminium oxide is a durable abrasive that remains sharp for longer. The resin bond provides a strong attachment of the abrasive grains to the backing, allowing the belt to withstand higher pressures and temperatures without delaminating, thus offering a longer service life.
How many belts are included in this pack?
This is a 10-pack, meaning you receive ten sanding belts in total.
What is the difference between 80 grit and finer grits?
Grit refers to the size of the abrasive particles. A lower number (like 80) indicates coarser grit, suitable for removing material quickly. Higher numbers indicate finer grit, used for smoothing surfaces and preparing them for finishing.
Troubleshooting
Sanding belt is not tracking correctly (slipping off drums or running too far to one side)
Check belt alignment and tension. Adjust the tracking knob on your sander, typically located near the front or rear drum, to guide the belt towards the center. Ensure the belt is seated correctly on both drums.
Belt is tearing or breaking prematurely
Verify that the belt size (100mm x 620mm) is correct for your sander. Ensure the belt is not overloaded by applying excessive pressure. Check for any burrs or damage on the sander's drums or rollers.
Poor sanding performance (slow material removal, excessive heat)
The belt may be worn out or clogged with dust and debris. Clean the belt with a brush or replace it if the abrasive is dull. Ensure you are using the correct grit for the material and task.
Sanding marks are uneven or inconsistent
Ensure the belt is properly tensioned and tracking straight. Avoid dwelling too long in one spot and maintain consistent pressure and movement across the workpiece. Check the sander's rollers for damage or debris.
Pros and Cons
Pros
- Provides excellent durability for demanding woodworking tasks.
- The 80-grit size is effective for rapid material removal and smoothing.
- The resin bond ensures consistent sanding performance.
- The 10-pack offers good value and convenience.
- Designed for compatibility with standard portable belt sanders.
Cons
- May not be suitable for very fine finishing work.
- Requires careful measurement to ensure correct fit for non-standard machines.
- Aluminium oxide can wear down over time, requiring replacement.
- Not intended for use on metal or other non-wood materials.
Setup, Compatibility & Care
Setup:
- Ensure your belt sander is unplugged before changing the sanding belt.
- Release the tension on the belt mechanism.
- Remove the old belt and place the new 100mm x 620mm belt onto the drums, ensuring the grit side is facing outwards.
- Re-apply tension to the belt mechanism and check alignment.
- Plug in the sander and briefly run it to ensure the belt tracks correctly. Adjust tracking if necessary according to your sander's manual.
Compatibility:
These belts are designed for portable belt sanders that use the 100mm x 620mm belt size. Always confirm your sander's belt dimensions before purchase to ensure a proper fit.
Care:
- Sanding belts are consumable items and will wear out over time.
- Clean dust and debris from the belt surface periodically using a wire brush or compressed air to maintain performance.
- Store belts in a dry place to prevent damage to the adhesive and abrasive.
- Replace belts when they become clogged, torn, or the abrasive dulls, which will be indicated by reduced cutting power and increased heat buildup.