Diamond Twist Drill Bit - 8pcs - 0.8/1.0/1.2/1.5/1.8/2.0/2.5/3.0mm - eMagTech
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This set of 8 eMagTech diamond twist drill bits is designed for hobbyists and crafters who need to create precise small holes in hard materials like glass, stone, and metal. The key benefit is their durability and sharpness, allowing for efficient drilling. A notable caveat is that drilling efficiency and lifespan are dependent on material hardness and proper usage, with coolant recommended for optimal results.
All features
| Brand | eMagTech |
|---|
Extended Product Information
FAQs
What is the smallest and largest drill bit size in this set?
The set includes sizes from 0.8mm (smallest) to 3.0mm (largest).
Can I use these bits on wood or plastic?
While designed for harder materials, these bits can be used on softer materials like wood or plastic, but they may remove material more aggressively than standard twist drills. Use with caution and low speed.
How do I prevent the drill bit from overheating?
For hard materials like glass or stone, it is highly recommended to use a coolant (like water or a specialized cutting fluid) and maintain a steady, moderate speed. Avoid forcing the bit.
What type of rotary tool is needed?
These bits are compatible with most standard rotary tools including hand drills, drill presses, flex shafts, bench drills, and hanging mills.
How long should these diamond bits last?
The lifespan of the diamond bits depends heavily on the material being drilled, the technique used, and whether coolant is applied. With proper care and usage on appropriate materials, they can last for many projects.
Do I need to use a special drill for these bits?
No, these bits are designed to fit into the standard chucks of most common rotary tools.
Are these bits suitable for drilling through metal?
Yes, they are suitable for drilling through various metals, particularly thinner sheets. For thicker or very hard metals, using coolant and a slower speed is essential.
Troubleshooting
Drill bit is not cutting effectively.
Ensure the bit is spinning in the correct direction and that you are using appropriate speed and pressure for the material. Try adding coolant. Check if the bit is dull or damaged.
Drill bit breaks during use.
This can happen if excessive force is applied or if the bit overheats. Ensure you are not forcing the bit and that adequate cooling is being used for hard materials. Start with smaller diameter bits for tougher jobs.
Bit wobbles in the tool.
Check that the bit is fully and securely inserted into the chuck and that the chuck is tightened properly. Ensure the bit shank is clean and undamaged.
Excessive heat buildup.
Reduce drilling speed and apply coolant. Ensure the bit is not bogged down and chips are being cleared efficiently.
Pros and Cons
Pros
- Durable diamond construction for longevity.
- Sharp bits ensure efficient drilling.
- Wide range of sizes for diverse projects.
- Compatible with most common rotary tools.
- Effective on hard materials like glass and stone.
Cons
- Drilling efficiency varies by material hardness.
- Bit lifespan can be affected by usage conditions.
- Coolant recommended for best performance and longevity.
- Not suitable for large diameter holes.
- Requires a compatible rotary tool.
Setup, Compatibility & Care
Setup: Securely insert the desired drill bit into the chuck of your compatible rotary tool. Ensure it is tightened firmly to prevent wobble or slippage during operation. Start with a slow speed and gradually increase as needed, depending on the material.
Compatibility: These bits are designed for use with standard rotary tools such as hand drills, drill presses, flex shafts, bench drills, and hanging mills. Ensure your tool's chuck can accept the shank diameter of the drill bits (typically 3/32 inch or 2.35mm for micro bits, though specific chuck compatibility should be verified).
Care: To maximize lifespan and performance:
- Always use coolant (water or specialized cutting fluid) when drilling into very hard materials like glass, stone, or dense metals.
- Avoid excessive pressure; let the diamond grit do the work.
- Periodically clean the bits to remove debris.
- Store bits in a dry place to prevent corrosion.