D-C-Fix Light Maple Wood Sticky Back Furniture Wrap Vinyl - VINYL WAREHOUSE.CO.UK
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This D-C-Fix Light Maple Wood self-adhesive vinyl film from VINYL WAREHOUSE.CO.UK is ideal for homeowners, renters, and DIY enthusiasts looking to quickly and affordably update surfaces like kitchen cabinets, furniture, or craft projects. Its key benefit is the ease of application and realistic wood design, offering a fresh look with minimal effort. A potential caveat is its heat resistance limit of 75 degrees Celsius, requiring care in very hot environments.
All features
| Model Part Number | 5417 |
|---|---|
| Brand | VINYL WAREHOUSE.CO.UK |
Extended Product Information
FAQs
Can this vinyl be used on kitchen countertops?
Yes, it can be used on kitchen countertops, but be mindful of its heat resistance limit of 75°C. Avoid placing hot pans directly on the surface.
How long does the adhesive last?
When applied correctly to a suitable surface, the adhesive is designed for long-term durability. Its fully removable nature means it can be taken off without damaging the underlying surface.
What is the maximum length I can order?
The vinyl is sold by the metre, and you can order multiple metres consecutively, up to a maximum length of 15 metres in a single piece.
Is this vinyl suitable for outdoor use?
This product is designed for indoor use. Outdoor exposure to UV rays and weather conditions may affect its appearance and adhesion over time.
Can I apply it over existing wallpaper?
It is best applied to smooth, non-porous surfaces. Applying over textured wallpaper may result in an uneven finish and reduced adhesion. The wallpaper should be removed and the wall prepared.
How do I remove the vinyl if I move house?
Gently heat the vinyl with a hairdryer on a low setting while peeling it back slowly. This will soften the adhesive, making removal easier and cleaner.
Troubleshooting
Air bubbles or wrinkles after application
Gently lift the affected section of the vinyl before it adheres fully and reapply, smoothing with a squeegee. For small bubbles, you can try pricking them with a fine needle and smoothing them out.
Vinyl not sticking well
Ensure the surface is thoroughly cleaned and dried. For slightly porous surfaces, a primer might be beneficial. Make sure you have removed all dust and grease.
Difficulty cutting the vinyl cleanly
Use a sharp craft knife or rotary cutter and a cutting mat for precise trimming. Replace the blade if it becomes dull.
Removable vinyl leaving residue
Most residue can be removed with a gentle adhesive remover or warm, soapy water. Test on an inconspicuous area first.
Pros and Cons
Pros
- Easy to apply and reposition for perfect results.
- Provides a realistic and attractive wood finish.
- Durable and simple to clean.
- Suitable for renters due to its removable nature.
- Available in custom lengths to suit project size.
Cons
- Limited heat resistance (75°C) may not be suitable for all applications.
- Requires careful application to avoid air bubbles and wrinkles.
- The realistic design might not perfectly match existing natural wood.
- Long-term adhesion on certain surfaces might require a primer.
Setup, Compatibility & Care
Setup:
- Ensure the surface to be covered is clean, dry, and smooth. Remove any grease or dust.
- Measure the surface and cut the vinyl film to the required size, adding a little extra for trimming.
- Peel back a small portion of the backing paper (approximately 10cm).
- Carefully position the film onto the surface and begin to smooth it down.
- Gradually peel off the remaining backing paper while simultaneously smoothing the vinyl with a squeegee or soft cloth, working from the center outwards to avoid air bubbles.
- Trim any excess material using a sharp craft knife or scissors.
Compatibility:
This vinyl is suitable for application on a wide range of smooth surfaces, including:
- Laminates
- Painted wood or MDF
- Glass
- Metal
- Plastic
- Tiles
It is not recommended for rough, unsealed, or textured surfaces.
Care:
To clean, simply wipe the surface with a damp cloth and mild detergent if necessary. Avoid abrasive cleaners or scouring pads. Due to its heat resistance limit of 75°C, avoid placing very hot items directly onto the surface. Ensure adequate ventilation around heat sources like ovens or radiators.