FamoWood Glaze Coat Kit - 1 Gallon Clear
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
The FamoWood Glaze Coat Kit - 1 Gallon Clear is designed for DIY enthusiasts and crafters seeking a durable, high-gloss finish for various projects. Its key benefit is providing the equivalent of 60 coats of varnish in a single pour, simplifying the finishing process. A notable caveat is the long drying time required before handling.
All features
| Model Part Number | 5050110 |
|---|---|
| Brand | FamoWood |
Extended Product Information
FAQs
What is the coverage rate for the 1-gallon kit?
A 1-gallon kit provides coverage of approximately 36 square feet at a thickness of 1/16 inch.
How long does it take to fully cure?
The product is dry to the touch in a minimum of 72 hours. However, it requires several days to fully cure and reach maximum hardness. Avoid heavy use or placing heavy objects for at least 7 days.
Can I apply another coat if needed?
Yes, you can apply multiple coats, but ensure each coat is fully cured before applying the next. Sand lightly between coats for optimal adhesion if the previous coat has fully hardened.
Is this product suitable for outdoor use?
FamoWood Glaze Coat is designed for indoor use. It resists temperatures up to 120 °F but may not withstand prolonged extreme weather conditions or UV exposure.
How do I clean up excess product or tools?
Uncured product can be cleaned with denatured alcohol or acetone. Once cured, it is very difficult to remove.
Can I embed objects in the glaze coat?
Yes, this is one of its primary uses. Embed non-waxy items like coins, photos, rocks, or shells. Ensure items are clean and dry before embedding.
What is the shelf life of the product?
Store unopened containers in a cool, dry place away from direct sunlight. The product typically has a shelf life of one year when stored properly.
Troubleshooting
Sticky or soft surface after drying
This is often due to incorrect mixing ratio, insufficient mixing, or low ambient temperatures. Ensure a precise 1:1 mix and thorough stirring. Maintain a room temperature between 70-80 °F (21-27 °C) during application and curing.
Bubbles in the finish
Bubbles are typically trapped air. Gently stir the mixture to minimize air incorporation. Use a heat gun or propane torch held at a slight angle to briefly pass over the surface, popping the bubbles. Avoid overheating.
Uneven or streaky finish
Ensure the surface is level and the product is spread evenly. The self-leveling properties should handle most minor imperfections, but uneven pouring can lead to streaks. Gentle agitation with a spreader can help if needed, but avoid overworking.
Poor adhesion or peeling
The surface may not have been properly prepared or was waxy. Ensure the surface is completely clean, dry, and free of any contaminants like silicone or wax. Lightly sanding non-waxy surfaces can improve adhesion.
Cloudy or hazy finish
This can occur if the product is exposed to moisture during curing, or if mixed improperly. Ensure adequate ventilation but avoid high humidity. Double-check the mixing ratio and stir thoroughly.
Pros and Cons
Pros
- Achieves a professional-level high-gloss finish with minimal effort.
- Significantly reduces application time compared to traditional varnishes.
- Excellent for embedding objects like coins, photos, or decorative items.
- Durable finish that protects surfaces from wear and tear.
- Easy to mix and apply due to its self-leveling properties.
Cons
- Requires a long drying time (minimum 72 hours to touch) before the surface can be handled.
- Primarily designed for indoor use; not recommended for extreme outdoor conditions.
- Requires careful surface preparation to ensure proper adhesion.
- Can be sensitive to temperature fluctuations during curing.
- The 'one pour equals 60 coats' is a measure of thickness, not necessarily a direct performance equivalent in all scenarios.
Setup, Compatibility & Care
Setup:
- Ensure your project surface is clean, dry, and free from dust, oil, wax, or any other contaminants.
- Mix equal parts of Component A and Component B (1:1 ratio) thoroughly. Stir gently but continuously for approximately 3-5 minutes, ensuring to scrape the sides and bottom of the mixing container.
- Pour the mixed product onto the center of your project, allowing it to flow to the edges. Use a heat gun or torch briefly to remove any air bubbles that may rise to the surface.
Compatibility:
- Suitable for most non-waxy surfaces including wood, painted surfaces, sealed countertops, ceramics, and more.
- Avoid use on waxy or silicone-based materials, as adhesion will be compromised.
- Test on a small, inconspicuous area first if unsure about material compatibility.
Care:
- For cleaning, use a soft, damp cloth. Avoid abrasive cleaners or scouring pads, which can scratch the finish.
- The coating resists temperatures up to 120 °F (49 °C). Avoid prolonged exposure to extreme heat.
- Protect the surface from heavy impacts during the initial curing period.