Shopping.co.uk

Bath Trap - FloPlast - 40mm

Bath Trap - FloPlast - 40mm

Part of the drainage system, this level bath waste trap from FloPlast is made from hard-wearing po...

Best current price£8.98from B&Q

Best offers

Shopping.co.uk recommended and popular offers

All Offers

5 offers from £8.98 - £13.80

View price history by clicking the chart icon.

B&QB&Q - Bath Trap (Dia)40mm
Free delivery in 1–3 days
£8.98
Visit shop
eBayFloPlast Low Level Bath Trap with Access 40mm TLB45
Free delivery in 1–3 days
£11.53
Visit shop
The RangeFloplast Low Level Bath Trap With Access 40Mm - Tlb45 - Durable Bathroom Drainage - Grey
Free delivery in 1–3 days
£11.91
Visit shop
OnBuy.comFloplast Low Level Bath Trap With Access 40Mm Tlb45 5055149901478
Free delivery in 1–3 days
£13.19
Visit shop
Professional Building SuppliesFloplast White Bath Trap - 50Mm Seal X 40Mm
Free delivery in 1–3 days
£13.80
Visit shop

Product Information

Full details

This guide helps you understand and effectively use the FloPlast 40mm Bath Trap. Designed for easy installation in UK drainage systems, it's ideal for homeowners and plumbers looking for a reliable waste solution. The trap's 50mm deep seal offers added protection against odors, a key benefit over traditional designs. However, proper installation and regular checks are essential to ensure leak-free performance.

All features

BrandFloPlast

Extended Product Information

FAQs

What tools do I need for installation?

You may need a pipe cutter, a screwdriver, and possibly pliers for tightening the nuts. Make sure you have appropriate PPE such as gloves.

Can I use this trap with a different brand of waste pipe?

Yes, this trap is designed to be compatible with most UK manufacturers' push-fit and solvent weld waste pipes.

How do I clean the trap?

You can remove the trap and flush it with water. Use a mild detergent to clean any build-up. Avoid using harsh chemicals or abrasive cleaners.

What should I do if the trap leaks?

First, tighten the connections. If the leak persists, disassemble the connection, inspect the seals for damage, and reassemble carefully. If the issue continues, consider replacing the seal.

What is the purpose of the O-ring?

The O-ring provides a watertight seal between the trap and the waste fitting, preventing leaks.

How often should I inspect the bath trap?

It is advisable to inspect the trap at least every six months, or whenever you notice a problem like slow draining or unpleasant odors.

Where can I buy replacement parts?

Replacement seals and other parts can be purchased from most plumbing supply stores or online retailers that sell FloPlast products.

Troubleshooting

Leakage at the joints.

Check the tightness of all nuts. Ensure the rubber seals are properly seated and not damaged. If necessary, disassemble the joint, inspect the seal, and reassemble, ensuring a snug fit.

Slow draining.

Check for any blockages in the trap. Remove the trap and clean out any debris. Inspect the waste pipe for obstructions as well.

Odors emanating from the drain.

Ensure the 50mm seal is intact. Check for any leaks that could be allowing sewer gases to escape. Make sure the trap has water in it to act as a barrier.

Difficulty connecting the trap to the waste pipe.

Ensure the pipe end is clean and free of burrs. Use a lubricant (such as silicone grease) on the pipe end and the seal to ease the connection. Make sure you are using the correct size pipe for the trap.

Pros and Cons

Pros

  • Durable polypropylene construction ensures longevity.
  • 50mm deep seal provides superior odor protection.
  • Compatible with both plastic and copper pipes.
  • Easy to install with compression fittings.
  • Made by FloPlast, a reputable UK manufacturer.

Cons

  • Requires careful installation to prevent leaks.
  • May require some tools for proper fitting.
  • Compression fittings can be susceptible to leaks if overtightened.
  • Seal may degrade over time and need replacement.

Setup, Compatibility & Care

  1. Preparation: Ensure you have all necessary components, including the trap, waste fitting, and appropriate pipes.
  2. Top Connection: Start by connecting the trap to the waste fitting. Make sure the O-ring is correctly seated inside the top trap nut. Push the lug into the waste fitting and tighten the nut by hand, avoiding over-tightening.
  3. Pipe Connection: Unscrew the nut from the trap and remove it, along with the washer and rubber seal. Place these components over the end of the waste pipe in the correct order: nut, washer, then seal.
  4. Assembly: Push the pipe into the trap as far as it will go. Slide the seal and washer forward into position and tighten the nut.
  5. Final Checks: Double-check that the central joint in the body of the trap is tight. If it's a telescopic trap, also ensure the joint at the trap neck is tight.
  6. Compatibility: This trap is designed to be compatible with most UK manufacturers' push-fit and solvent weld waste pipes. It is suitable for use with both plastic and copper pipes.
  7. Care: Regularly inspect the trap for any signs of leaks or damage. Clean the trap periodically to remove any build-up that may restrict flow. Avoid using harsh chemicals for cleaning.

Price History

DatePrice
Visit shop