Solvent Weld Waste Pipe Coupler - FloPlast - White
Not Available
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This guide is for DIY enthusiasts and plumbing professionals needing to connect 32mm solvent weld waste pipes. The FloPlast Solvent Weld Waste Pipe Coupler offers a secure and clean method for diverting waste water, ensuring a leak-free system. A potential caveat is the need for specific solvent cement, which is not included.
All features
| Model Part Number | WS07W |
|---|---|
| Brand | FloPlast |
Extended Product Information
FAQs
What type of adhesive should I use with this coupler?
You must use a solvent weld cement specifically designed for ABS or PVC waste pipes. Refer to the solvent cement manufacturer's instructions for the correct application.
Can I use this coupler with push-fit waste pipes?
No, this coupler is designed for solvent weld systems only and is not compatible with push-fit or compression fittings.
What is the outside diameter of the pipe this coupler fits?
This coupler is designed for UK standard 32mm (1.25 inch) nominal bore solvent weld waste pipe.
How many couplers are included in a pack?
Each pack contains 5 solvent weld waste pipe couplers.
Do I need to prime the pipes before applying solvent cement?
While some systems recommend a primer, check the solvent cement manufacturer's guidelines. For many ABS applications, a primer may not be strictly necessary if pipes are clean and dry, but it can enhance the bond in some conditions.
What is the temperature range for using solvent weld cement?
Most solvent weld cements perform best at room temperature (above 5°C/40°F). Check the specific product's datasheet for optimal temperature ranges and potential issues in cold weather.
Is this coupler suitable for underground drainage?
These couplers are typically used for above-ground domestic waste systems. For underground applications, specific drainage systems and materials may be required; consult local building regulations.
Troubleshooting
Leak at the joint
Ensure sufficient solvent cement was applied evenly to both surfaces and the pipe was held firmly during the initial set. Check for cracks in the coupler or pipe end. If a leak occurs, the joint may need to be cut out and redone.
Pipe won't insert fully
Check for obstructions or burrs inside the coupler or on the pipe end. Ensure the pipe is cut squarely. Re-apply solvent cement if necessary after cleaning.
Joint feels weak or loose after curing
Insufficient solvent cement or inadequate holding time during installation are likely causes. The joint should be redone with proper application and curing.
Pros and Cons
Pros
- Ensures a reliable, leak-free joint for waste pipes.
- Made from durable ABS plastic for long-term use.
- Complies with UK standard 32mm waste pipe dimensions.
- Comes in a convenient pack of 5 for multiple installations.
- Easy to integrate into existing white plumbing systems.
Cons
- Requires separate purchase of appropriate solvent weld cement.
- Only compatible with 32mm solvent weld pipe, not push-fit or other sizes.
- ABS material can be brittle in extreme cold if not handled carefully during installation.
- White color may show dirt more readily than darker options in some environments.
Setup, Compatibility & Care
Setup:
- Preparation: Ensure both ends of the 32mm solvent weld waste pipe are clean, dry, and free from burrs. Cut the pipe squarely.
- Dry Fit: Test fit the pipe ends into the coupler to ensure they seat fully.
- Apply Solvent Cement: Apply a thin, even layer of appropriate 32mm solvent weld cement to the outside of the pipe ends and the inside of the coupler sockets.
- Join: Immediately push the pipe ends into the coupler sockets with a slight twisting motion until they bottom out.
- Hold: Hold the joint firmly for 30 seconds to prevent movement while the cement sets.
- Cure: Allow the joint to cure fully according to the solvent cement manufacturer's instructions (typically several hours) before running water through the pipe.
Compatibility:
- Pipe Size: Exclusively designed for 32mm (1.25 inch) UK standard solvent weld waste pipe.
- Material: Compatible with ABS and PVC solvent weld waste pipes.
- Not Compatible: Not suitable for push-fit waste systems, compression fittings, or other pipe diameters.
Care:
- Cleaning: Wipe the exterior with a damp cloth if necessary. Avoid abrasive cleaners.
- Maintenance: The solvent weld joint is permanent; no regular maintenance is required beyond ensuring no blockages occur within the waste system itself.