White Self-Adhesive Draught Seal - 10m x 9mm x 4mm
Best current price£6.00from B&Q
Best offers
Shopping.co.uk recommended and popular offers
B&Q£6.00Visit shop - White Self-Adhesive Draught Seal (L)10M (W)9mm (T)4mm
Visit shopB&Q£6.00Visit shop One Offer
1 offer from £6.00
View price history by clicking the chart icon.
B&Q - White Self-Adhesive Draught Seal (L)10M (W)9mm (T)4mm
Free delivery in 1–3 days
£6.00
Visit shop
Product Information
Full details
This 10m roll of white self-adhesive draught seal is designed for homeowners looking to improve energy efficiency and reduce external noise. It offers a simple, cost-effective way to block gaps around doors and windows, preventing heat loss in winter and keeping cool air in during summer. While easy to apply, its effectiveness relies on proper surface preparation and application for a lasting seal.
All features
| Model Part Number | 5059304274668 |
|---|---|
| Brand | B&Q |
Extended Product Information
FAQs
What is the primary benefit of using this draught seal?
The primary benefit is improved energy efficiency by preventing heat loss or gain through gaps, and a reduction in noise pollution.
How long is the roll of draught seal?
The roll contains 10 meters of draught seal.
What are the dimensions of the seal?
The seal measures 9mm in width and 4mm in thickness.
Can this be used on exterior doors?
Yes, it can be used on exterior doors and windows, provided the application surface is clean and smooth for optimal adhesion.
Do I need any tools to apply this?
No, the seal has a self-adhesive backing and can be applied by hand. Scissors or a craft knife are useful for cutting it to the required length.
How should I clean the seal?
Wipe gently with a slightly damp cloth. Avoid abrasive cleaners or excessive moisture.
Will this seal prevent water ingress?
While it helps block air, it is not designed as a primary waterproofing solution and may not prevent significant water ingress during heavy rain.
Troubleshooting
Seal not sticking properly
Ensure the surface is thoroughly cleaned and dried before application. Remove any existing dust, grease, or old adhesive. Press the seal firmly into place for at least 30 seconds along its entire length.
Draughts still noticeable
Check if the seal is applied correctly to all potential gaps around the window or door. Ensure the seal is the appropriate size for the gap and is compressed when the window/door is closed. Reapply or add additional seals if necessary.
Seal detaches after a short period
The surface may not have been prepared adequately, or the area experiences extreme temperature fluctuations. Reapply to a meticulously cleaned surface. For very high-traffic areas, consider using a stronger adhesive designed for foam applications, applied to the back of the seal.
Seal is too thick/thin for the gap
This seal is designed for specific gap sizes (approx. 2-5mm). If the gap is too large, consider a wider or thicker draught excluder. If the gap is too small, the seal may prevent the window/door from closing properly.
Pros and Cons
Pros
- Easy to cut and apply without special tools.
- Significantly improves insulation against cold draughts.
- Noticeable reduction in external noise.
- Cost-effective solution for energy saving.
- Flexible material adapts well to uneven surfaces.
Cons
- Requires clean, dry surfaces for optimal adhesion.
- Adhesive may degrade over time or in extreme temperatures.
- White colour may not suit all interior aesthetics.
- May require replacement after several years of use.
- Not suitable for very wide or deep gaps.
Setup, Compatibility & Care
Setup:
- Ensure the surface where the seal will be applied (e.g., window frame, door jamb) is clean, dry, and free from dust or grease.
- Measure the required length of seal.
- Cut the seal to size using scissors or a craft knife.
- Peel back a small section of the protective backing paper.
- Carefully align the seal with the edge of the surface and press firmly into place, gradually removing the backing paper as you go.
- Ensure the seal is applied evenly and without stretching.
Compatibility:
This draught seal is suitable for use on most common household surfaces, including painted wood, metal, and uPVC, provided they are smooth and clean. It is designed for gaps typically between 2mm and 5mm wide, fitting within its 4mm thickness. Not recommended for rough or porous surfaces where adhesion may be compromised.
Care:
Wipe the seal occasionally with a slightly damp cloth to remove dust. Avoid using harsh cleaning chemicals or abrasive materials, as these can damage the foam or its adhesive backing. Inspect the seal periodically for signs of wear or detachment, and reapply or replace as needed.