Car Gods Pro Preparation & Ceramic Coating Protection Hydrophobic Bundle Kit - GODBUN36
Summon forth Aion, God of eternity and bearer of Ceramico Pro. The Ceramico Pro Ceramic Coating is...Summon forth Aion, God of eternity and bearer of Ceramico Pro. The Ceramico Pro Ceramic Coating is a blend of highly durable nano-polymers specifically designed to chemically bond to your paintwork. This creates a protective barrier that guards your vehicle against swirl marks, scratches, dirt, and other contaminants, whilst also enhancing the depth of gloss and prolonging the paintwork's flawless finish. IMPORTANT NOTE Always follow the Preparation instructions to ensure Ceramico Pro performs correctly. Applying Ceramico Pro to damaged/dirty surfaces will permanently lock in any damage, dirt, or defects. Wear gloves to prevent oils from your hands from interfering with Ceramico Pro. Never apply Ceramico Pro in direct sunlight. Plan your work area before you begin; work in sections of 50cm x 50cm (mask off work sections if necessary). *Ceramico Pro Ceramic Coating will last up to 3 years if applied according to the instructions below or by an accredited Car Gods detailer and properly maintained. Do not contact wash your vehicle with any cleaning chemicals for the first 7 days after application as this could affect the performance and longevity of the ceramic coating. HOW TO USE - PHASE 1 Phase 1 – Preparation Fully decontaminate your vehicle's paintwork before applying Ceramico Pro. It is vitally important that you follow the below steps exactly as stated to ensure that Ceramico Pro performs correctly. What you will need for this phase: Gloves Wash Mitt Car Gods Almighty Power Pre-Wash Car Gods Arctic Storm Snow Foam Car Gods Pure Shampoo Two-Buckets with Grit Guards Car Gods Fall Out Eliminator Car Gods Clay Bar Kit Car Gods Ceramico Pro Pre-Cleanse Car Gods Pure Compound NOTE: Always refer to the directions for use provided on the back label of each of the above products before using them. Use only as directed. I) Spray Car Gods Almighty Power Pre-Wash directly onto your paintwork to remove any stubborn soils or stains (i.e. bird lime and tree sap). II) Use Car Gods Arctic Storm Snow Foam to remove traffic film build up from your paintwork. III) Contact wash your vehicle using the Two-Bucket method and Car Gods Pure Shampoo and rinse thoroughly. IV) Apply Car Gods Fall Out Eliminator to remove any iron particles in the paintwork. V) Use Car Gods Clay Bar Kit to remove any contaminants embedded in the paintwork. VI) Apply Car Gods Tar Remover to remove stubborn tar spots from your paintwork. VIl) Degrease the surface using Car Gods Ceramico Pro Pre-Cleanse. VIII) Machine polish the vehicle using Car Gods Pure Compound to remedy any paint defects, light scratches, or oxidation. IX) Spray Car Gods Ceramico Pro Pre-Cleanse once more to remove any oils that may impair the performance of Ceramico Pro. TIP: For best results, we recommend rinsing the vehicle after every step to ensure the coating has a thoroughly prepared surface to bond to. HOW TO USE - PHASE 2 Phase 2 – Applying Ceramico Before beginning this phase, make sure you have fully completed Phase 1. Ensure you have thoroughly cleaned and dried all areas of your paintwork. Make sure any defects have been attended to. Applying Ceramico Pro to damaged/dirty surfaces will permanently lock in any damage, dirt, or defects. Wear gloves to prevent oils from your hands from interfering with Ceramico Pro. Never apply Ceramico Pro in direct sunlight. Plan your work area before you begin; work in sections of 50cm x 50cm (mask off work sections if necessary). What you will need for this phase: Gloves Ceramico Pro Polysilazane + Applicator Pad Applicator Cloth Microfibre Buffing Cloth I) Wrap the applicator cloth tightly around the applicator pad. II) Shake the bottle well, then load up the cloth with 10-12 drops to initially dampen the cloth. Hint: Always add more drops as needed to keep the cloth saturated. For subsequent loading, you will need fewer drops to keep the cloth damp. III) Apply a thin layer across the surface using straight-line motions. Apply firstly towards and away from yourself, then rotate the applicator 90° and apply left to right to ensure an even application. Apply Ceramico Pro in an overlapping crosshatch pattern to ensure you have completely covered the section. IV) Once Ceramico Pro has been applied to the entire section, allow it to sit between 2 to 5 minutes, or until the treated area looks iridescent. Use the microfibre cloth to buff off the excess coating from the surface. Repeat steps III and IV for each subsequent section of the vehicle until you have applied Ceramico Pro to the entire vehicle. NOTE: Always work and complete one section at a time, do not start applying Ceramico Pro Ceramic Coating to a different section before buffing off the section you've already applied the coating to. V) Allow overnight or a minimum of 12 hours for Ceramico Pro to fully cure to the vehicle. During this time, do not allow any water, dust, and other contaminants to come into contact with the treated paintwork. Contaminants will have a detrimental effect on the coating. Do not cover the vehicle for 7 days after treatment. For the best maintenance of the Ceramic Coating, ensure you wash your vehicle following steps I to IV of Phase 1. Only suitable for gloss paintwork; do not apply to any plastic or rubber elements on your vehicle.
Best current price£114.98from My Motor World
Best offers
Shopping.co.uk recommended and popular offers
My Motor World£114.98Visit shop ›Car Gods Light Ceramico Pro Prep & Ceramic Coating Bundle
Visit shop ›