FloPlast Solvent Weld Access Plug - 40mm

The FloPlast ABS Solvent Weld Access Plug is a versatile and durable solution for gaining access t...

Best current price£2.33from Professional Building Supplies

All Offers

16 offers from £2.33 - £10.80

View price history by clicking the chart icon.

Professional Building SuppliesFloplast Grey Solvent Weld Waste Access Plug - 32Mm
Free delivery in 1–3 days
£2.33
Visit shop
eBayFloPlast ABS Solvent Weld Access Plug 32mm Grey
Free delivery in 1–3 days
£4.87
Visit shop
The RangeFloplast Abs Solvent Weld Access Plug 32Mm Grey - Ws30 - Grey
Free delivery in 1–3 days
£5.16
Visit shop
OnBuy.comFloplast Abs Ws30g Solvent Waste Access Plug - 32Mm 5055149902123
Free delivery in 1–3 days
£5.71
Visit shop
B&QB&Q - Abs Solvent Weld Access Plug 40mm Grey
Free delivery in 1–3 days
£5.91
Visit shop

Product Information

Full details

The FloPlast 40mm Solvent Weld Access Plug is designed for plumbers and DIY enthusiasts needing reliable access points in waste systems for inspection and cleaning. Its key benefit is providing a durable, easy-to-install solution for maintenance. A caveat is that solvent weld joints are permanent, requiring precise application.

All features

Model Part NumberABS WS31G
BrandFloPlast

Extended Product Information

FAQs

What is a solvent weld access plug used for?

It is used to create an access point in waste systems for inspection and cleaning, often referred to as a 'cleaning eye'.

How is this access plug installed?

It is installed using solvent cement (SC250), applied to both the pipe and fitting surfaces, then pushed together with a slight twist. The joint is permanent.

What pipe sizes is this plug available in?

The FloPlast Solvent Weld Access Plug is available in 32mm, 40mm, and 50mm sizes.

Can I disconnect this joint later?

No, solvent weld joints are permanent and cannot be demounted once the joint has been made and set.

What safety precautions should I take when using solvent cement?

Always work in a well-ventilated area, keep cement away from heat and flames, and avoid contact with skin. If contact occurs, wash thoroughly with soap and water.

How long does the joint need to set before testing?

The joint should be left for 12 hours before testing the waste system.

Is this product manufactured to specific standards?

Yes, the solvent weld waste system is manufactured in the UK to BS EN 1455 and is Kitemarked.

Troubleshooting

Leak at the joint

Ensure surfaces were clean before applying solvent. Re-applying solvent cement may be necessary if the joint was not properly sealed during initial application (note: this is difficult once fully set).

Difficulty inserting pipe

Ensure no excess solvent has pooled inside the fitting socket, as this can soften the pipe and fitting, making insertion difficult. Ensure the pipe is not damaged.

Plug is difficult to remove for access

This is expected if it was permanently sealed. Consider using a plug with a removable cap for easier future access if needed.

Pros and Cons

Pros

  • Lightweight yet strong design
  • Cost-effective solution for maintenance access
  • Simple and straightforward installation process
  • Compatible with a range of solvent weld waste pipe sizes
  • Ensures efficient waste system maintenance

Cons

  • Solvent weld joints are permanent and cannot be demounted
  • Requires careful application of solvent cement
  • Only compatible with solvent weld systems
  • Requires a well-ventilated area for installation due to solvent use

Setup, Compatibility & Care

Setup:

  1. Ensure the outer wall of the pipe and the inner wall of the fitting are clean and free from debris.
  2. Apply FloPlast SC250 solvent cement evenly to both surfaces.
  3. Push the pipe fully into the fitting socket.
  4. Give the pipe a slight twist to ensure full contact.
  5. Clean off any excess solvent with a damp cloth.
  6. Allow the joint to set for at least 5 minutes before disturbing.
  7. Leave the installation for 12 hours before testing the system.

Compatibility:

  • Compatible with FloPlast solvent weld waste pipes and fittings.
  • Available in 32mm, 40mm, and 50mm diameters.
  • Available in grey, white, and black finishes to match existing systems.

Care:

  • No specific maintenance is required for the access plug itself. Regular cleaning of waste systems using appropriate methods is recommended.
  • Ensure the cap or plug is securely fitted after use to maintain a seal.

Price History

DatePrice
Visit shop