Screwless Flat 3 Gang 10 Amp Metal Rocker Switch - Black
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This AET Screwless Flat 3 Gang 10 Amp Metal Rocker Switch in Black is designed for homeowners and electricians seeking a modern, sleek, and reliable lighting control solution. Its primary benefit is the clean, screwless aesthetic that enhances any room's decor, while offering versatile 2-way switching. A potential caveat is the requirement for a minimum 25mm deep back box for installation. This guide covers its key features, performance, setup, and maintenance.
All features
| Colour | Silver |
|---|---|
| Model Part Number | SL3GSWIBS |
| Brand | AET |
Extended Product Information
FAQs
What does 'screwless' mean for this switch?
The 'screwless' design means that once installed, there are no visible screws on the face of the switch plate. The plate clips or snaps directly onto the mounting grid, providing a very clean and modern appearance.
Can this switch be used for standard 1-way lighting?
Yes, while designed with 2-way switching capability, it can be wired for simple 1-way operation if only one switch is controlling the light.
What type of lights can I control with this switch?
This 10 Amp rated switch is suitable for most standard domestic lighting circuits, including incandescent, halogen, and LED lights. Ensure the total load does not exceed 10 Amps.
Do I need special tools to install this switch?
Standard electrical tools such as screwdrivers (for wiring connections) and wire strippers are required. No specialized tools are needed for the screwless plate itself.
What is the finish of the metal plate?
The plate has a brushed satin matt chrome stainless steel effect finish, providing a sophisticated and durable look.
Is this switch compatible with dimmer functions?
This is a standard on/off rocker switch. For dimming functionality, a separate dimmer switch would be required. Ensure any dimmer used is compatible with your chosen light source (e.g., dimmable LEDs).
What is the minimum depth required for the back box?
A minimum back box depth of 25mm is required to ensure the switch can be properly and safely installed, accommodating wiring.
Troubleshooting
Switch not working
Ensure mains power is restored and check all wiring connections are secure. Verify the correct terminals have been used for 1-way or 2-way switching.
Flickering lights
Check all wire connections are tight. If the issue persists, the bulb or connected lighting fixture may be faulty.
Switch plate won't snap on
Confirm that the back box is flush with the wall surface and is at least 25mm deep. Ensure no wires are obstructing the plate.
One light circuit doesn't turn off
This typically indicates an incorrect wiring configuration for 2-way switching. Double-check the wiring against a 2-way switching diagram or consult an electrician.
Pros and Cons
Pros
- Modern and sleek screwless aesthetic.
- Durable metal construction with a stylish finish.
- Allows independent control of three lighting circuits.
- Flexible 2-way switching capability.
- Easy to clean and maintain.
Cons
- Requires a minimum 25mm deep back box, which may necessitate minor adjustments during installation.
- Metal plate may be susceptible to fingerprints (though less noticeable on matt finishes).
- Limited to 10 Amp rating, not suitable for high-power loads.
- Primarily designed for lighting circuits, not general power outlets.
Setup, Compatibility & Care
Setup:
- Safety First: Always turn off the mains power at the consumer unit before starting any electrical work.
- Wiring: Connect the wires according to standard 2-way switching (or 1-way if preferred) principles, ensuring secure connections within the terminals.
- Back Box: Ensure the existing or new back box is at least 25mm deep to accommodate the switch and wiring.
- Mounting: Carefully align the switch plate with the back box and gently push until it clicks into place. The screwless design means no screws are visible externally.
Compatibility:
- Compatible with standard UK/EU wiring systems.
- Designed for 230V AC lighting circuits.
- Requires a minimum 25mm deep wall back box.
Care:
- Wipe clean with a soft, damp cloth. Avoid abrasive cleaners or solvents which can damage the finish.
- Ensure the area around the switch is kept dry.