Roco Geoline Point Decoder - HO/OO Gauge - RC61196
Best current price£36.95from eBay
Best offers
Shopping.co.uk recommended and popular offers
eBay£36.95Visit shop Roco Geoline Point Decoder HO/OO Gauge RC61196
Visit shopeBay£36.95Visit shop One Offer
1 offer from £36.95
View price history by clicking the chart icon.
Product Information
Full details
The Roco Geoline Point Decoder (RC61196) is designed for HO/OO gauge model railway enthusiasts using the Roco geoLine track system. It provides precise control for turnouts, offering a key benefit of simplified layout automation and integration with digital command control systems like the Roco multiMAUS. A potential caveat is its specific compatibility with the geoLine system and turnout drive 61195.
All features
| Model Part Number | 61196 |
|---|---|
| Brand | Roco |
Extended Product Information
FAQs
What is the main purpose of the Roco Geoline Point Decoder RC61196?
Its main purpose is to digitally control the switching of Roco geoLine turnouts, allowing for remote operation and integration into automated digital model railway layouts.
What specific turnout drive is required for this decoder?
This decoder is designed to work with the Roco turnout drive 61195.
Can I control this decoder with a standard analog DC controller?
No, this is a digital decoder and requires a DCC (Digital Command Control) system. It is not compatible with analog DC controllers.
How do I set the address for the decoder?
The address is set by programming the decoder's Consist Variables (CVs) using a DCC command station that supports programming, such as the Roco multiMAUS.
What is the maximum number of turnouts this decoder can control?
This is a single point decoder, meaning it controls one turnout. It can be assigned one of 1024 possible turnout addresses.
Can I use this decoder with turnouts other than Roco geoLine?
No, this decoder is specifically designed for the Roco geoLine track system and its compatible turnout drive 61195.
Does the decoder support route control?
Yes, it supports route control functionality when used in conjunction with compatible Roco systems like the multiMAUS.
Troubleshooting
Turnout does not switch when commanded.
Verify power supply to the DCC system and the track. Ensure the turnout address programmed into the decoder matches the address being sent from the controller. Check all wire connections between the decoder, turnout drive, and DCC system for looseness or damage. Confirm the turnout drive 61195 is functioning correctly.
Decoder is unresponsive to commands.
Check that the decoder is correctly wired into the DCC system. Reset the decoder by reprogramming its address or consulting the manual for a specific reset procedure. Ensure the DCC command station is functioning correctly and sending signals.
Turnout switches erratically or partially.
This may indicate a weak signal or power issue. Check wiring integrity. Ensure the turnout drive is properly seated and not obstructed. Clean any debris that might be impeding the turnout's movement. If using CVs, ensure they are set correctly and not causing unexpected behavior.
Over-heating detected.
Disconnect power immediately. Check for any short circuits on the track or within the turnout mechanism. Ensure the decoder is not installed in an enclosed space with poor ventilation. If the problem persists after checking for shorts, the decoder may be faulty.
Pros and Cons
Pros
- Facilitates automated switching of turnouts in digital layouts.
- Programmable via CVs for advanced customization.
- Compact and easy to install.
- Includes essential safety features like over-heating and short-circuit protection.
- Supports route control for more sophisticated operations.
Cons
- Specifically designed for the Roco geoLine track system.
- Requires the Roco turnout drive 61195 for operation.
- Not directly controllable via locomotive addresses.
- May require knowledge of DCC programming (CVs) for full functionality.
Setup, Compatibility & Care
Setup:
- Ensure the Roco turnout drive 61195 is correctly installed and connected to the geoLine track.
- Connect the Roco Geoline Point Decoder (RC61196) to the turnout drive according to the manufacturer's instructions.
- Connect the decoder to your DCC control system's track power and command bus.
- Program the decoder with a unique turnout address (1-1024) using your DCC controller (e.g., Roco multiMAUS).
Compatibility:
- Primary Compatibility: Roco geoLine track system, specifically with turnout drive 61195.
- Digital Systems: Compatible with DCC command stations, particularly those supporting RocoNet-System like the Roco multiMAUS.
- Not Compatible: Will not work with analog DC (Direct Current) systems or Märklin's Digital system without appropriate adapters or interfaces.
Care:
- Keep the decoder clean and free from dust and debris.
- Avoid exposure to excessive moisture or extreme temperatures.
- Regularly check connections to ensure they are secure.
- The decoder is protected against over-heating and short-circuits, but avoid sustained short-circuit conditions which can stress the components.