Hycote Red Spray Paint - 400ml
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This guide is for car enthusiasts and DIYers looking to customize or protect brake components. The Hycote Red Spray Paint offers a durable, high-gloss finish for brake calipers and drums, providing an eye-catching aesthetic. A key consideration is its specialized application; it's designed specifically for brake parts and should not be used on other surfaces.
All features
| Colour | Red |
|---|---|
| Model Part Number | XUK440-PK4 |
| Brand | Motor World |
| Container Volume | 400 |
Extended Product Information
FAQs
What surfaces can this paint be used on?
This Hycote Red Spray Paint is specifically designed for automotive brake calipers and brake drums. It is not intended for general automotive bodywork or other surfaces.
How many coats should I apply?
It is recommended to apply multiple thin, even coats. Allow approximately 10-15 minutes between coats for best results and durability. Refer to the product can for specific recommendations.
How long does it take to dry?
The paint is fast-drying. It is typically touch-dry within 15-20 minutes, but allow at least 2-4 hours before handling and a full 24 hours for complete curing before significant use or exposure to moisture.
Does this paint require a primer?
For optimal adhesion and finish, it is recommended to ensure the brake components are thoroughly cleaned and free of rust. While a specific primer isn't always mandatory if the surface is properly prepared, using a high-temperature brake caliper primer can enhance durability.
Is this paint resistant to brake dust and cleaning chemicals?
Yes, the extremely durable formulation provides good resistance to brake dust, road grime, and common automotive cleaning chemicals once fully cured.
What is the volume of the spray can?
Each can contains 400ml of Hycote Red Spray Paint.
Can I use this paint on other car parts besides brakes?
No, this product is specifically formulated for brake calipers and drums. Using it on other parts not designed for this type of paint may lead to poor performance, premature failure, or safety issues.
Troubleshooting
Uneven or patchy finish
Ensure the can was shaken sufficiently before and during use. Apply in thin, even coats, maintaining a consistent distance from the surface. Allow adequate drying time between coats.
Paint not adhering properly
The surface may not have been adequately cleaned or prepared. Re-clean the surface thoroughly to remove all grease, oil, and contaminants. Ensure the surface is completely dry before application.
Clogging of the nozzle
After use, turn the can upside down and spray for a few seconds to clear the nozzle. If clogged, remove the nozzle and soak it in a suitable solvent (like lacquer thinner), then dry and reattach.
Runs or drips appearing
Applied coats too heavily. Lighten the application pressure or increase the distance between the can and the surface. Allow the paint to fully dry and then carefully wet-sand the runs with fine-grit sandpaper before applying a new, thin coat.
Pros and Cons
Pros
- Provides a professional-looking, high-gloss finish.
- Excellent durability and resistance to fading.
- Specifically formulated for brake caliper and drum applications.
- Meets environmental VOC regulations.
- Fast-drying formula for efficient use.
Cons
- Limited to brake caliper and drum application; not suitable for general automotive painting.
- Requires proper surface preparation for optimal adhesion and finish.
- Potential for overspray if not applied carefully in a well-ventilated area.
- Color may vary slightly depending on lighting conditions.
- Not intended for use on high-temperature engine components.
Setup, Compatibility & Care
Setup:
- Ensure the area is well-ventilated and protected from overspray.
- Thoroughly clean and degrease the brake calipers or drums. Remove any rust, dirt, or old paint.
- Mask off any surrounding components that should not be painted.
- Shake the can vigorously for at least two minutes before use.
Compatibility:
- This product is designed specifically for automotive brake calipers and brake drums.
- It is not suitable for use on engine parts, exhaust systems, or other surfaces exposed to extreme, prolonged heat beyond typical brake component temperatures.
- Ensure the surface is free of oil, grease, and contaminants for proper adhesion.
Care:
- Once fully cured, the painted surface can be cleaned with standard automotive cleaning products.
- Avoid using abrasive cleaners or tools that could scratch the high-gloss finish.
- Regular washing will help maintain the paint's appearance.