End Feed Equal Tee - PlumbRight - 10mm
Best current price£1.00from City Plumbing GB
Best offers
Shopping.co.uk recommended and popular offers
City Plumbing GB£1.00Visit shop Plumbright Endfeed Equal Tee 10Mm 30051705
Visit shopCity Plumbing GB£1.00Visit shop All Offers
2 offers from £1.00 - £1.68
View price history by clicking the chart icon.
City Plumbing GBPlumbright Endfeed Equal Tee 10Mm 30051705
Free delivery in 1–3 days
£1.00
Visit shop
Product Information
Full details
This guide is for plumbers and DIY enthusiasts building or modifying hot and cold water systems. The PlumbRight 10mm End Feed Equal Tee allows for the creation of strong, leak-free pipework junctions. A key consideration is that installation requires soldering and a blowtorch, necessitating appropriate safety measures and skills.
All features
| Model Part Number | 30051705 |
|---|---|
| Brand | PlumbRight |
Extended Product Information
FAQs
What tools are essential for installing this tee?
You will need a blowtorch, solder suitable for plumbing (e.g., lead-free for potable water), flux, emery cloth or pipe cleaning brush, and pipe cutters.
Can I use this tee for gas or central heating systems?
This fitting is specifically approved for hot and cold water systems. For gas or central heating, consult the specific product requirements as different materials and standards may apply.
What does WRAS approved mean?
WRAS (Water Regulations Advisory Scheme) approval means the product has been tested and meets stringent standards for use with public water supplies in the UK, ensuring it does not contaminate drinking water.
How do I ensure a leak-free joint?
A leak-free joint relies on thorough cleaning of the pipe and fitting, proper application of flux, adequate and even heating of the joint, and sufficient solder drawn into the joint by capillary action.
What is the significance of BSEN1254: Part 1?
This is a European standard that specifies requirements for copper and copper alloy pipe fittings. Compliance ensures the fitting meets specific quality, dimensional, and performance criteria.
Can this fitting be used with plastic pipes?
No, this is an end feed fitting designed specifically for copper pipe. Adaptors would be required for connecting to plastic pipework, or alternative fittings should be used.
Troubleshooting
Joint leaks after soldering
The joint was likely not heated sufficiently, the pipe/fitting was not clean, or flux was not applied correctly. The joint will need to be unsoldered, cleaned thoroughly, and resoldered.
Solder not flowing into the joint
Ensure adequate heat is applied to the fitting. The fitting or pipe may be too cold, or there might be an obstruction. Reheat and try applying solder again.
Fitting becomes discolored during heating
This is usually due to oxidation from overheating or poor flux application. While often cosmetic, excessive discoloration can indicate potential weakness. Ensure even heating and proper fluxing.
Difficulty seating pipe into fitting
Check for any burrs or damage on the pipe end, or debris inside the fitting cup. Clean both thoroughly.
Pros and Cons
Pros
- Creates strong, leak-free connections when installed correctly.
- WRAS approved for safe use with drinking water.
- Durable construction suitable for hot and cold systems.
- Standardized end feed design for reliable jointing.
- Complies with BSEN1254: Part 1 for quality assurance.
Cons
- Requires soldering skills and equipment (solder, blowtorch).
- Installation can be hazardous if proper safety precautions are not taken.
- Not suitable for push-fit or compression plumbing systems.
- Installation may require specific building code knowledge.
- Requires careful cleaning of pipe and fitting for a good joint.
Setup, Compatibility & Care
Setup:
- Ensure the pipe ends and the inside of the tee's cups are clean and free from dirt or oxidation. Use emery cloth or a pipe cleaning brush.
- Apply a thin, even layer of appropriate flux to the pipe ends and inside the fitting.
- Assemble the pipe into the tee, ensuring it is fully seated.
- Heat the joint evenly with a blowtorch, focusing on the fitting body where the pipe enters.
- Apply solder to the opposite side of the joint from the heat source. The solder should be drawn into the gap by capillary action.
- Allow the joint to cool naturally without disturbing it.
Compatibility:
- Compatible with 10mm copper pipe manufactured to relevant British Standards.
- Suitable for use with hot and cold water systems.
Care:
- No specific ongoing care is required for the fitting itself once installed.
- Regularly check connected pipework and joints for any signs of leaks or corrosion as part of routine plumbing maintenance.